background image

INTRODUCTION

We take pride in designing and building the highest quality fitness equipment on the market. This
means that you will enjoy years of low maintenance and minimal repair from every one of our
products. Only the highest quality products have the Keiser name on them.

This manual will assist you with the assembly, maintenance and safe operation of the Keiser
Infinity Series.  We strive to continuously improve our products, therefore, parts and machine
designs are subject to change without notice.  Please call our Service Department at (800) 888-
7009 or visit our website at 

www.keiser.com

 for the latest product information.

CAUTIONS, WARNINGS AND NOTES

Please read all instructions contained in this manual prior to assembling and using this product.
Failure to follow these instructions will invalidate the product warranty and could lead to serious
injury.

We use the term 

Caution!

 to document things that could cause bodily injury to persons on or

around the equipment if the information contained herein is ignored.

The term 

Warning!

 is used to ensure the proper installation of components for maximum

machine life and user safety.

Note!

 is used to document things that we recommend and things to be aware of before

performing a particular instruction.

WARRANTY

All products manufactured by Keiser Corporation shown in this manual are warranted against
defects in materials and workmanship as follows (providing the damage was not caused by
abuse, misuse, or neglect of normal care) :

Structural Integrity of Frame Members – 10 years;
Cylinders, Gauges, and all Electrical Components – 3 years (1 year if compressed air is not
dried);
Compressor and Dryer, Cables, Pulleys, and Bearings – 2 years;
Pneumatic Valves and Chrome – 1 year;
Paint, Upholstery, Seat Belts, Hand Grips, and other Rubber and Plastic Products – 90 days

The warranty terms begin with the date of original delivery to be evidenced by appropriate
shipping documents. Any alteration of the equipment so listed without express written consent of
Keiser Corporation shall constitute a waiver by the buyer of this warranty. This warranty does not
cover other brand name products distributed by, but not manufactured by Keiser Corporation
which are subject to their respective manufacturers’ warranties. During the warranty period,
warranted defects will be repaired at Keiser Corporation, Fresno, Calif., or the defective part will
be replaced, at the option of the manufacturer, without charge for either parts or labor to repair
the defective part. This warranty does not cover the removal of the defective part and the
installation of the repaired part. All claims under the warranty must be in writing and authorization
obtained from the manufacturer, Keiser Corporation, to return defective parts for exchange.
Defective parts must be returned to Keiser Corporation.

User’s agents, or anyone directing the use of said equipment shall determine the suitability of the
product for its intended use, and said parties are specifically put on notice that they shall assume
all risk and liability in connection herewith. There are no warranties that attach to this product
from the manufacturer either express or implied other than those specifically set forth above.

Содержание Infinity Series
















Отзывы: