background image

Benchy Sparkling - Instruction Manual 

 

Page 

14

 of 

16

 

www.KegLand.com.au

  

Last Updated 3/06/2022 6:03 PM

 

 

Step 4. Spray all connections with soapy water and look for the formation of bubbles. This includes 
all push fit connections and connections between the regulator and CO2 cylinder. 

If bubbles are formed at any of these connections this indicates a leak which needs to be fixed.  

Step 5. Look for the formation of bubbles in the water in the reservoir. Air bubbles being formed in 
the reservoir indicates a leak from the 2L Ball lock keg inside the reservoir. 

Adjusting the Reservoir Set Temperature 

The reservoir ideally should be set at 2°C to ensure the sparkling/still water within the soda 
carbonator keg is cold without freezing the reservoir or carbonated water.  

The reservoir should not be set below 2°C as there is a risk of the water freezing which can 
damage the Benchy Sparkling. 

To change the reservoir set temperature refer to the following instruction manual. 

KegLand STC1000 Instructions

 

Benchy Sparkling Initial Startup Procedure 

1.

 

 Ensure the mains water supply and CO2 gas supply are turned off and the Benchy Sparkling 
is connected to your dispensing taps. 

2.

 

Set the pressure on your CO2 regulator to your desired carbonation level (30-50psi). A 
higher gas pressure correlated to a higher carbonation level and fizzier water. 

3.

 

Turn your mains water supply on and set the water pressure using an inline regulator to 
about 10-15 psi higher than the pressure set on your CO2 regulator. 

4.

 

Open your taps for a few seconds to purge any air which is in the hosing between the 
Benchy Sparkling and the tap. 

5.

 

Enjoy a continuous supply of cold soda water and cold still water. 

Expected time to carbonate after initial setup  

After setting up your soda carbonator it may take up to 24 hours for the water to be fully 
carbonated.  

Plumbing options without access to a mains water 

supply 

 If you do not have access to a mains water supply for example if you are using tank water or bore 
water, we would suggest using a 12V self-priming diaphragm pump to increase the water pressure to 
10-15 psi above the pressure on your regulator. It is suggested that the pump you choose has an 
output pressure of at least 80psi and it has an auto pressure switch. The auto-pressure switch 
ensures that the pump provides a constant water pressure and switches off once that pressure 

Содержание KL20671

















Отзывы: