Kees van der Westen Speedster Скачать руководство пользователя страница 4

Страница: 4 / 21

INSTALLATION

Speedster

page 4

Unpack

Tools needed



Phillips screw driver no. 2

Procedure

1.  Remove the lid of the crate.
2.  Remove the side panels.
3.  Lift the machine by its legs.

Warnings!

The valves at both sides of the group are not designed to lift the machine. Lifting the machine by these
may cause the frame to bend which results in unrepairable damage.

Although sturdy, the brew lever might bend when lateral force is applied. A bent brew lever may lead
to malfunction of the lever.

Parts included in standard shipment

Accessories



Stainless steel filter holder, 2-cup spout



Stainless steel filter holder, 1-cup spout



Water pump with electric motor



Two high-pressure water supply hoses, each 1.5 m (5 ft)



One high pressure water supply hose, 0.5 m (20 in)



Discharge hose, inner diameter 16 mm (0.64 in)



Stainless steel hose clamp for discharge hose



KVDW Stainless steel tamper



Blind filter



Jar with cleaning powder



Group brush



Group screen extractor



Drain hose



Speedster T-shirt



2 KVDW shot glasses



USB flash drive with comprehensive user and maintenance manual

Spare parts



there is a Barista Kit included with the machine to facilitate routine maintenance

Содержание Speedster






















Результаты поиска

Содержание Speedster

Отзывы:

Бренды по названию

Популярные бренды

Kees van der Westen Speedster, Инструкция по установке и эксплуатации

Результаты поиска

Содержание Speedster

Отзывы:

Бренды по названию

Популярные бренды