manualshive.com logo in svg

Kees van der Westen Slim Jim mirage, Руководство пользователя

Поделиться
Скачать
Kees van der Westen Slim Jim mirage Скачать руководство пользователя страница 27

USER MANUAL 

– check condition 

Slim Jim User manual 

 

page 26 

Check machine condition, report malfunctions 

It will help the service technician solving problems if some information about the machine is known 
before a house-call is scheduled. This information should include: 

1.  serial number of the machine 
2.  free flow rate of each individual group 
3.  a well-defined description of the malfunction 

 

Free-flowrate 

During “free-flow” (no filter holder locked in the group) the flowrate gives an indication of the smallest 
orifice in the coffee system of the machine. This would normally be the flat-jet underneath the group-
valve which, depending on individual set-up, has a diameter of 0.6 

– 1.0 mm. With such small 

openings, even a minor divergence can cause quite a large difference in flowrate. Production 
variances of the flat-jets are known to cause a difference in free-flow flowrate and thus 

“free-flow shot 

time” between groups of up to 10%.  
The table below gives an indication of free-flowrates at brew temperature with different flat-jet sizes. If 
one or more groups have a free-flowrate that falls outside the range given for that flat-jet it is advised 
to have a technician check the machine. 

diameter of flat-jet  

(mm) 

minimum  

(ml/minute) 

goal  

(ml/minute) 

maximum  

(ml/minute) 

0.6 

300 

400 

450 

0.8 

700 

850 

925 

1.0 

1000* 

1200* 

1300* 

Table 2. Showing range of free-flowrates for water of 90-95°C at 9 bar brew pressure for different size 
flat-jets.* numbers not checked yet. 

 

Heating element indicator lights 

A set of indicator lights is found on the bottom of the electronics box, see Figure 20. 

If the machine is warmed up and functioning correctly, the 3 lights on the left (steam boiler) will light up 
simultaneously at longer intervals and 

“in sync” 

2

 with the corresponding orange centre line shown on 

the control panel. The 2 or 3 lights on the right (coffee boiler heating) will light up shortly at somewhat 
erratic intervals but in sync with the corresponding orange centre line on the interface. 

If there is a problem with the machine, the indicator lights help to determine possible causes. 

 

Figure 20. The heating element indicator lights on a Slim Jim Triplette, left indicator lights for the 
steam boiler, right for the coffee boilers. See also Figure 21. 

 

2

 The control panel-display is lagging by about 0.5 seconds w.r.t. the indicator lights. 

coffee

steam

gr1

gr2

gr3

lower

middle

upper

electrics tray

GROUP 1

93.4

GROUP 2

45.6

GROUP 3

93.2

STEAM

124.6

MENU

Содержание Slim Jim mirage


































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды