manualshive.com logo in svg

KEENCUT Javelin Integra, Инструкция пользователя

Поделиться
Скачать
KEENCUT Javelin Integra Скачать руководство пользователя страница 10

CUTTING 

The standard GRAPHIK blade holders can be set to cut at different depths and in either
direction by simply adjusting or flipping the blade over in the holder.  You can also push
or pull the cutting head to suit your own comfort.

Once the blade is set move the cutting head near to the start of the cut, press down 
the blade holder and push or pull to make the cut.  Only light finger pressure is usually
required to depress the blade holder so most of your effort can be directed into pushing
the blade through the material.

SCORING HARD PLASTICS

Many hard plastics such as Acrylic can be scored and snapped by hand or over the
edge of a bench (use hand and eye protection).  The back edge of the GRAPHIK blade
can be used as a scoring blade, position the plastic sheet in the cutter and draw the
blade backwards across the surface applying downward pressure to the blade holder,
some plastics will benefit from being scored a number of times before snapping.

4.2

Operation

4.2

DEEP CUT

SHALLOW CUT

SHALLOW CUT

DEEP CUT

MyBinding.com

5500 NE Moore Court 

Hillsboro, OR 97124 

Toll Free: 1-800-944-4573 

Local: 503-640-5920

Содержание Javelin Integra














Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды