manualshive.com logo in svg

Keba KeDrive D3-DA BG3, Руководство по эксплуатации

Поделиться
Скачать
Keba KeDrive D3-DA BG3 Скачать руководство пользователя страница 38

4.6.1 

24 V control supply

The supply units KeDrive D3-DP BG3 and BG4 need an external 24 V DC power supply 
unit for the 24 V DC supply (see Figure 4.9). Details are described in the Operation 
Manual KeDrive D3-DP (1804.201B.x). The 24 V are distributed to the entire axis group 
in the KeDrive D3 system via the busbars. 

Figure

Key

24 V  DC Netzteil 

(Power Supply)

1.

2.

3.

4.

X01C

(1)  24 V power supply unit (ext. not 

included in the scope of supply)

(2)  Controller KeDrive D3-DU
(3)  Supply unit  

KeDrive D3-DP BG3

(4)  Axis controller KeDrive D3-DA BG3

Note:

The 24

 

V

 

DC busbar fittings are to 

be tightened to a tightening torque of 

1.5 Nm.

Figure 4.9  Busbars, 24 V control supply

NOTE:

If an external 24 V supply is used, it must provide safe isolation as per 
EN 61800-5-1 or EN 50178. 

4.6.2 

Power supply

The supply voltage for the axis controllers is supplied by the supply unit KeDrive D3-DP 
via the busbars (DC link). This voltage, also called the DC link voltage, is between 
565 V DC and 678 V DC, depending on the mains supply to the KeDrive D3-DP 
(400 V AC and 480 V AC). 

Figure

Key

24 V  DC Netzteil 

(Power Supply)

24 V  DC Netzteil

(Power Supply)

2.

1.

DC-Link +

DC-Link -

3.

4.

(1)  DC link jumper
(2)  Controller KeDrive D3-DU
(3)  Supply unit KeDrive D3-DP BG3
(4)  Axis controller KeDrive D3-DA

 

BG3

Note:

The DC link busbar fittings are to be tightened to a 
tightening torque of 3.0

 

Nm. 

Figure 4.10  Busbars, power supply (DC link)

38

1  Electrical installation

Operation Manual KeDrive D3-DA BG3 and BG4 

1804.200B.1-01    Date: 03/2023

Electrical installation

Содержание KeDrive D3-DA BG3





















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды