background image

CLEANING

Proper care should be taken to fully clean the griddle on a regular basis..

DISCONNECT ELECTRIC POWER SOURCE BEFORE CLEANING.

CONTROL PANEL - Clean any grease build-up on the thermostat knobs.

NOTE:

If grease gets into the body of the thermostat, it may cause it to fail.

IF GREASE GETS INTO THE BODY OF THE THERMOSTAT, 
IT MAY CAUSE POSSIBLE ELECTRICAL SHOCK.

V SERVICE DIAGNOSIS

A.

Trouble-Shooting

The following diagnosis is only to be used as a guide to qualified service personnel. Keating recommends that you
use a qualified service company. 

PROBLEM

PROBABLE CAUSE

SOLUTION

Griddle won’t heat.

a. No electricity to griddle.

a. Connect griddle to an approved source of  

power.

b. Thermostat isn’t on.

b. Turn thermostat to desired cooking

temperature.

c. Thermostat is faulty.

c. Replace thermostat.

d. Connections are loose.

d. Tighten connections.

e. Element is faulty.

e. Replace element.

Temperature of griddle

a. Thermostat out of calibration.

a. Calibrate thermostat. 

is erratic.

See page 4–Calibration.

b. Thermostat bulb improperly 

b. Adjust thermostat bulb.

placed.

c. Exhaust problems or drafts.

c. Contact your HVAC representative.

Griddle is overheating.

a. Thermostat out of calibration.

a. Calibrate thermostat.

b. Thermostat is faulty.

b. Replace thermostat.

5

Содержание MIRACLEAN












Отзывы: