background image

   PROPER OPERATION 

Please use the replacement of parts on the manual to ensure the safety of instructors.

 

This product is 

for R/C model, so do not use for other purpose.

   SAFE OPERATION 

Operate  this  unit  within  your  ability.  Do  not  fly  under  tired  condition  or  improper  operation,  which 
may cause danger.

3.Safety Check Before Flying

Agile Helicopter is a Trademark of Flight Research Rc Europe , Proudly made by KDS Model Shenzhen

Page 02

Before flying, for safety reasons, make sure that no one else is operating a R/C model on the same frequency as yours.
Before flying, please check that the power of your transmitter and your helicopter are sufficient for the flight.
Before  turning  on  the  transmitter,  please  check  that  the  throttle  stick  is  in  its  lowest  position,  IDLE  UP  switch  must  be  on  OFF 
position.
When turning off the model, please follow the power on/off procedure. Power ON: turn on the transmitter first, then turn on
helicopter power. Power OFF: turn off the helicopter power first and then turn off the transmitter. Improper operating procedure
may cause the model to be out of control, so please do make this your habit.
Before operation, check that every  movement is smooth  and  directions are correct. Inspect  servos  carefully for interferences and 
broken gears.
Check for missing or loose screws and nuts. See if there is any cracked and/or incomplete assembly of parts.
Check main rotor blades and rotor holders carefully. Broken and premature failures of parts might result in a dangerous situation or 
crash.
Check all ball links to avoid excess play and replace as needed. Failure to do so will result in poor flight stability.
Check  that  the  battery  and  power  plugs  are  fastened.  Vibrations  and  violent  flight  might  loosen  the  plugs  and  so  lead  to  out  of 
control.
Check for the tension of main drive belt.

   PREVENT MOISTURE

R/C models are composed of many precision electrical components. lt is critical to keep the model and 
associated equipment away from moisture and other contaminants. The introduction or exposure to 
water or moisture in any form can cause the model to malfunction resulting in loss of use, or a crash. 
Do not operate or expose to rain or moisture.

   KEEP AWAY FROM HEAT 

R/C  models  are  made  up  of  various  forms  of  plastic.  Plastic  is  very  susceptible  to  damage  or 
deformation due to extreme heat and cold climate. Make sure not to store the model near any source 
of heat such as an oven, or heater. lt is best to store the model indoors, in a climate-controlled, room 
temperature environment.

4.Tools Required

-Hex drivers : 1.5, 2, 2.5, 3, 4mm
-Nut Drivers : 2, 4, 7mm
-Ball link pliers
-Diagonal cutting pliers
-Scissors
-Metric ruler
-Soldering iron + solder (for motor and ESC wiring)
-Pitch gauge (for set up)
-Swashplate leveller
-Threadlock blue * (medium)
-Threadlock red * (high strength)
-Bearing retainer compound
-Epoxy A+B Glue
-Grease
-Oil
*Colors may vary depending on your area.

Содержание AGILE 7.2




































Отзывы: