KB Genesis KBAC-24D Скачать руководство пользователя страница 21

Страница: 21 / 35

5.3 Motor Connection – Wire the motor to Terminal

Block TB1 Terminals U, V, W. See Figures 10 -12 on

page 20. Motor cable length should not exceed

100 ft (30 m) – special reactors may be required –

consult our Sales Department.

Be sure Jumper J2 is set to the corresponding

motor horsepower rating, as described in

Section 6.2 on page 23.

5.4 Remote Main Speed Potentiometer Connec-

tion – The drive is supplied with a prewired Main

Speed Potentiometer mounted on the front cover.

To operate the drive from a remote potentiom-

eter (5 kΩ), remove the white, orange, and violet

potentiometer leads from Terminals P1, P2, and

P3. The wires may be taped and left inside

the drive. The potentiometer assembly may

be removed if a watertight seal is used to

cover the hole in the front cover. Wire the

Main Speed Potentiometer to Terminals P1

(low side), P2 (wiper), and P3 (high side).

See Figure 13.

WARNING! Do not earth ground any

Main Speed Potentiometer terminals.

Application Note – If it is required that the

Remote Main Speed Potentiometer

be isolated from the AC Line, install the

SIAC-PS Signal Isolator with Power

Supply (See Table 2 on page 9).

5.5 Remote Start/Stop Switch

Connection –

The drive is supplied with a

prewired Start/Stop Switch

mounted on the front cover

to electronically start and

stop the drive.

To operate the drive from

a remote Start/Stop Switch

(type (ON)-OFF-ON, SPDT),

remove the white, black,

and red wires from Terminals

RUN, COM, and STOP. The

wires may be taped and left

inside the drive. The switch

assembly may be removed

if a liquidtight seal is used to

cover the hole in the front cover. After applying power to the drive, momentarily set the Start/Stop

Switch to the “START” position.

For Start/Stop Switch with normally closed stop contact, set Jumper J9 to the “NC” position.

See Figures 14 and 15. Also see Section 6.8 on page 25.

5.6 Automatic Restart – Automatic restart requires the elimination of the Start/Stop Switch. Remove

the white, black, and red wires from Terminals RUN, COM, and STOP. The wires may be taped and

left inside the drive. The switch assembly may be removed if a liquidtight seal is used to cover the

hole in the front cover.

HIGH VOLTAGE! See Warning on Page 19.

(Push to Stop)

Normally Closed

Momentary Contact

STOP

Normally Open

Momentary Contact

(Push to Start)

RUN

START

Figure 15 – Remote Start/Stop Switch Connection

with Normally Closed Stop Contact

(J9 Installed in “NC” Position)

Figure 13 – Remote Main Speed

Potentiometer Connection

Main Speed

Potentiometer

Orange (Wiper)

Violet (High)

White (Low)

HIGH VOLTAGE!

See Warning on Page 19.

Figure 14 – Remote Start/Stop Switch Connection

with Normally Open Stop Contact

(J9 Installed in “NO” Position)

Black

STOP

Red

START

RUN

White

HIGH VOLTAGE! See Warning on Page 19.

Содержание KBAC-24D




































Результаты поиска

Содержание KBAC-24D

Отзывы:

Бренды по названию

Популярные бренды

KB Genesis KBAC-24D, Руководство по установке и эксплуатации

Результаты поиска

Содержание KBAC-24D

Отзывы:

Бренды по названию

Популярные бренды