manualshive.com logo in svg

Kaysun KCCT-64 IPS, Инструкция по установке и эксплуатации, Страница: 3 / 36

Поделиться
Скачать
Kaysun KCCT-64 IPS Скачать руководство пользователя страница 3

WARNING

CAUTION

IMPORTANT

• This manual provides the installation instructions for this controller. 

Refer to the included wiring diagrams to connect the controller to the 

indoor unit. 

• The controller uses low voltage. Keep a minimum distance of 12” (305 

mm) between low voltage control wire and high voltage power wires.

• Ensure there are no gaps between the controller back cover and the 

mounting surface. 

• Ground the shielded control wiring. 

• 

Do not use a megger to test insulation. 

Do not install controller in areas where harmful gases containing 

sulfur or other damaging may exist ot the controller may be damaged. 

Clean controller using a clean, damp cloth. Do not spray cleanser on 

or around controller. 

Read all of the information in this manual before using this controller. All 

wiring must conform to local and national building and electrical codes 

and ordinances. This is a 12 VDC controller. Do not install on voltages 

higher than 12 VDC.

Содержание KCCT-64 IPS





































Отзывы:

Нет отзывов