KAYO MOTOR AY70-2 Скачать руководство пользователя страница 66

Страница: 66 / 80

ZHEJIANG KAYO MOTOR CO., LTD.

WWW.KAYOMOTO.COM

Carbon

deposit

working surface

It is impossible to fit the

valve and the valve seat

tightly.

The engine starts hard or fails to

start. Insufficient engine output;

Engine speed changes during idle

run

Remove the carbon

deposit

The working surface is over

worn or has pits, pock

marks, ablation or damage

It is impossible to fit the

valve and the valve seat

tightly.

The engine starts hard or fails to

start. Insufficient engine output;

Engine speed changes during idle

run

Replace the valve

The valve stem is over worn

The

fitting

clearance

between the valve stem and

the valve

guide

is too

wide

Sound of valve leakage, Thick

blue and white fume form the

exhaust muffler pipe

Replace the valve

The valve

stem

deformed

It is impossible to close the

valve completely

The engine starts hard or fails to

star

Replace the valve

Valve

spring

The

spring

ineffective or fractured

It is impossible to fit the

valve and the valve seat

tightly.

The engine starts hard or fails to

star. Sound of the cylinder head

Replace

the valve

spring

Содержание AY70-2

















































































Результаты поиска

Содержание AY70-2

Отзывы:

Похожие инструкции для AY70-2

Бренды по названию

Популярные бренды

KAYO MOTOR AY70-2, Руководство по обслуживанию

Результаты поиска

Содержание AY70-2

Отзывы:

Похожие инструкции для AY70-2

Бренды по названию

Популярные бренды