KAYO MOTOR AU110 Скачать руководство пользователя страница 5

Страница: 5 / 80

ZHEJIANG KAYO MOTOR CO., LTD.

WWW.KAYOMOTO.COM

Service Information

1.1 Operation note

1.2 VIN Number

1.3 Main parameters list

1.4 Maintenance parameters list 1.5 Torque tightening

1.6 Lubricant, sealant

1.7 Cable, hose and wiring diagram

1.1 Operation note

Security

1. Wearing work clothes (coveralls), hat and safety boots suitable for the operation.

In some conditions dust glasses, dust masks, gloves and other safety protective

supplies are needed to protect you from injury.

2. Do not let the engine long running in airtight spots or unventilated places.

3. In case of scald, don’t touch the engine when the engine just stops working.

4. Battery solution (dilute sulfuric acid) is a strong corrosive agent; contact with the

skin, splash into the eye burns may lead blindness. Once the battery solution is

accidentally touched on clothes or skin, rinse immediately with plenty of water. If the

battery solution is touched on eyes, please flush immediately with plenty of water and

get treatment in time. Storage battery and battery solution should be kept strictly,

keep out of reach of children. Battery charging will produce flammable and explosive

hydrogen, once there is a source of fire or spark close, there is an explosion risk.

Please charge it in well-ventilated places.

5. As gasoline is flammable and explosive, it is strictly prohibited to set off fireworks

in the work site. Pay attention to sparks as well as open flames. Besides, the

vaporized gasoline may explode, please choose well-ventilated sites.

6. Attention, the rear wheel, clutch or other rotating parts and movable parts may

clip hands and clothes during maintenance.

7. Two or more people must constantly greet each other when operating to ensure

safety.

Disassembly and installation instructions

1. All the Parts, lubricants and lipids must be Kayo brand parts or Kayo recommends.

2. When disassemble, Please sort out the parts of each system and kept separately

to ensure that all parts can be put back.

3. Keep the vehicle clean before inspection.

4. The Gasket, o-ring, piston pin baffle ring, cotter pin and other parts must be

replaced after disassembling.

5. Snap ring will be deformed if the opening is too big during disassembly and easy to

fall off after reassemble. Please do not use snap ring which was inelastic.

6. After disassembly and inspection, clean the parts and blow the cleaning agent

away with compressed air before measurement. Grease the moving surface before

assembly.

7. During disassembly, check all the necessary sites and measure relevant data,

make sure the reassembly condition as same as previous state.

8. Bolts, nuts, screws and other fasteners shall be pre-tightened and then tightened

in accordance with the specified tightening torque on the diagonal in accordance with

the principle of from large to small and from inside to outside.

Содержание AU110

















































































Результаты поиска

Содержание AU110

Отзывы:

Похожие инструкции для AU110

Бренды по названию

Популярные бренды

KAYO MOTOR AU110, Руководство по обслуживанию

Результаты поиска

Содержание AU110

Отзывы:

Похожие инструкции для AU110

Бренды по названию

Популярные бренды