Kayline 442-210, Руководство по установке

Страница: 4 / 7

Pg 4 442-210
Step 6. Windshield Slot.
Position windshield slot (Item 17) on top of windshield frame centered form side to side,
and with the weather stripped edge toward the vertical flange on top of frame. Place windshield channel (Item 18) under
windshield slot The channel will act as a shim to provide proper clearance between windshield frame and windshield slot
Starting at the center, mark and drill 1/8" hole. Secure slot to flange on windshield frame with a #10 x 1/2" sheet metal
screws (Item 4). Mark drill and install sheet metal screws in remaining holes following same procedure as above making
sure that gap between windshield slot and windshield frame remains the same from side to side. Windshield channel
should slide under windshield slot easily with little resistance. Form ends of slot around flange on windshield frame. See
figure 4-A and 4-B.
Step 7. Horizontal Rods.
Measure 1/2" in from side of windshield frame and 1/2" in from inside of windshield frame.
Mark and drill 3/8" hole. See figure 4-A. While pulling front bow forward, place front of horizontal rod (Item 19) into hole in
windshield frame. Place the rear of horizontal rods into hole in front bow. See figure 4-B and 4-D. Repeat for the other
side. There is one left and one right horizontal rod. The right is painted white on the end that is placed into hole in wind-
shield frame. Repeat for other side.
Step 8. Vertical Rods.
With door closed, find position of vertical rod (Item 20) by holding it in place at rear of door
frame vertical to the horizontal rod. Mark and drill 3/8" hole in body at this point Remove washer and wing nut from
horizontal rod. Place vertical rod into hole drilled in body and over bolt on horizontal rod. Attach vertical rod to horizontal
rod with washer and wing nut previously removed. Repeat for other side. Again the right side vertical rod is marked white
at the end that is placed into hole in body See figure 4-G.
Step 1. Channel Installation.
Place top on hood of
vehicle, vinyl side down. Slide sewn in rope (at front of top)
into windshield channel (item 18). See figure 4-B. Slip
channel under windshield slot. Flip top up and over bows.
Snap rear bow flap to rear bow. See figure 4-C.
Step 2. Top Installation.
Pull to the rear and down on
rear bottom corners of side panels until 2 1/2” pieces of
plastic are fully engaged on corner plate. See figure 5. Clip
long plastic pieces from rear to front until all are fully
engaged on body aluminum. Insert tailgate retainer
(Item 21) into fabric loop on rear curtain. See figure 4-F.
Slip tailgate retainer between tailgate clips and tailgate.
See illustration 4-H. Lock rear bows into position as shown
in illustration 4-F. Thread buckle straps through footman
loops footman loops. Tighten only enough to hold rear bow
in place. See figure 5. If over tightened, it could cause top
to tear or strap to be pulled from top. Close zippers on both
sides of rear curtain.
If top is too tight and you are unable to clip plastic
to corner plates or body aluminum it may be necessary to
remove your horizontal and vertical rods to allow the front
bow to fall forward and relieve tension on the top. After
removing horizontal and vertical rods clip plastic to corner
plates and body aluminum. Once all plastic is clipped into
place, push front bow to the rear and install horizontal and
vertical rods. Then proceed as directed above. After initial
installation the top should form to hardware and installation
should become easier.
Step 3. Horizontal And Vertical Flaps.
Wrap
vertical rod flap around vertical rod and press hook and
loop together. Wrap horizontal rod flap around horizontal
rod and press hook and loop together.
Step 4. Snap Stud At Windshield Corner.
Locate
for snap stud (Item 22) by pulling forward and down on
front of convertible top. Mark and drill 1/8” holes. Install 3/8”
sheet metal screw studs and snap top to studs. Repeat for
the other side. See figure 4-A.
Figure 5
FABRIC INSTALLATION