Kawai GS100 Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 27

background image

１６

１２．

Hammer Rest Rail

Set the hammer rest rail 5mm below the hammer
shanks in the rest position.

１３．

Hammer Letoff

Adjust hammer letoff Distance.

To improve accuracy, place a light directly above
the string and watch the string’s shadow on the
hammer felt.

Press each key down slowly with one hand while
adjusting the letoff dowel with the other hand to
set the letoff distance.

In the bass section letoff should be 2.0mm - 2.5m,
middle and treble 1.0mm - 1.5mm.

«
...
14
15
16
17
18
...
»

Содержание GS100




























Отзывы:

Нет отзывов

Похожие инструкции для GS100

Бренд: Atomos Страницы: 4

Бренд: Kawai Страницы: 33

Бренд: Kawai Страницы: 60

Бренд: SAGEMCOM Страницы: 33

Бренд: Shimpo Страницы: 68

Vigilantplant NFBU200-S Series

Бренд: YOKOGAWA Страницы: 24

Бренд: horiba Страницы: 117

Бренд: Sequid Страницы: 111

Dakota Ultrasonics ZX-2

Бренд: ABQ Industrial Страницы: 27

Бренд: SecureAlert, Inc. Страницы: 7

Бренд: GANN Страницы: 89

Smart Air Quality Monitor

Бренд: Lennox Страницы: 28

Бренд: Roland Страницы: 96

Бренд: Michell Instruments Страницы: 28

Бренд: 3nh Страницы: 39

Бренд: Saluki Technology Страницы: 161

UNITY INOVA NMR

Бренд: Varian Страницы: 65

Бренд: Sonel Страницы: 56

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды