manualshive.com logo in svg
background image

2

 

CAUTION

 NOTICE (NOTE)

These international safety symbols are used through-
out this manual to inform the end user, installer, and 
owner of important safety information and notices for 
safe and effective use of the equipment.

Important Safety Instructions

 CAUTION

Under NO circumstances should anyone 

• 

enter the water with the electrical equipment 
plugged in and/or in operation.  It is NEVER 
recommended to enter the water with the 
equipment in operation.
Caution should be used when dealing with any 

• 

electrical equipment with moving parts.
NEVER run the unit out of water.  It will 

• 

damage the seals and create a dangerous 
situation for the operator.
Extreme caution should be used around water, 

• 

especially cold water, such as in Spring, Fall, 
and Winter, which poses a hazard in and of 
itself.
NEVER lift or drag the unit by the power or 

• 

light cord.  If you need to pull the unit to the 
side of the pond, use the anchoring ropes.
Do not use waders in deep ponds/lakes or 

• 

ponds/lakes with drop-offs, drastic slopes, or 
soft bottom material.
Do not use boats that tip easily for fountain 

• 

installation, such as a canoe, and follow all 
boating safety rules and regulations, including 
wearing a PFD. (Personal Flotation Device)
The unit is supplied with an internal grounding 

• 

conductor.  To reduce the risk of electrical 
shock, be certain that the unit is plugged/
connected to an approved RCD (GFCI) 
protected circuit.  
A properly sized 3 phase motor control 

• 

(motor starter) with overload and short 
circuit protection must be provided at time of 
installation.
3 phase units (2.3, 3.3, 5.3) require a startup 

• 

test after wiring to ensure proper rotation of 
the impeller.  If the impeller is rotating in the 
opposite direction, the unit will not perform 
properly and internal damage to the unit may 
occur.  (See 3 phase startup procedure)
Means for disconnection must be incorporated 

• 

in the fi xed wiring in accordance with local 
and national wiring rules to prevent accidental 
start.
Consult a qualifi ed electrician for electrical 

• 

installation.

General description of equipment 

and function

Fountain/decorative aerator
Electrically driven submersible pump designed to im-
prove water quality with water movement and aeration 
in a decorative display.

Intended use and limits of use

Kasco equipment is only intended for specifi c uses as 
detailed in this owner’s manual.  Intentional misuse 
could result in injury, damage to the product, and sur-
rounding property.  

Intended uses are as follows:
Fountains/decorative aerators:  To provide aeration 
and a decorative display to ponds, lakes, and similar 
bodies of water.  Fountains and decorative aerators are 
provided with additional guarding to prevent acciden-
tal contact while operating.

Installation, adjustment, maintenance, and removal of 
this equipment should be limited to experienced main-
tenance persons or trained professionals.  If you are 
not sure how to install or operate any Kasco products 
call your local distributor, contact an electrician, or 
contact Kasco customer service at www.kascomarine.
com for further assistance. 

Installation requirements:

Read and understand all instructions and safety 

• 

warnings prior to installation and use.
Equipment must be installed as required by the 

• 

instructions.
Do not use this equipment outside of its intended 

• 

purpose, or if site conditions would pose a danger-
ous installation.  

Содержание 8400EJ





























Отзывы: