Karel MS38s Скачать руководство пользователя страница 45

Страница: 45 / 78

Karel MS38s Programming Guide

Edition 3.1

I.3.

AUTO ATTENDANT RECORD GAIN

(OPERATOR ONLY)

(86447)

Allows adjusting the voice record level of Auto Attendant messages.

86447 P

•

ARAMETERS

= 1,2,…,8 : The voice record level, where 1 is the lowest voice

level and 8 is the highest voice level.

•

EFAULT

86447 4 is active.

•

OTES

IMPORTANT

The operator should disable Auto Attendant before entering this program.

I.4.

AUTO ATTENDANT MESSAGE

ENTRY

(864)

Allows recording Auto Attendant messages which are read to the parties who call
the system through Auto Attendant lines under appropriate states of Auto Attendant
operation.

864 P + Message

•

ARAMETERS

= 00

Auto Attendant Greeting Message.

= 01

Missing Digit Message.

= 02

Busy Extension Message.

= 03

: No Answer Message.

= 04

: Invalid Number Message.

= 05

Wait Message.

= 06

Inaccessible Extension Message.

= 07

Transfer Message.

= 08

Night Mode Greeting Message.

= 09

DISA Greeting Message

= 10

Password Message.

= 11…23

General purpose messages.

Содержание MS38s















































































Результаты поиска

Содержание MS38s

Отзывы:

Бренды по названию

Популярные бренды

Karel MS38s, Руководство по программированию

Результаты поиска

Содержание MS38s

Отзывы:

Бренды по названию

Популярные бренды