Kärcher Trailer HDS Series Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 32

Kärcher Trailer HDS Series Скачать руководство пользователя страница 17

17

Operations

Assembly Instructions

STEP 1:

Attach a 5/8" garden hose

to inlet connector. Minimum flow
should be 5 gpm.

STEP 4:

Check oil level on sight

glass on backside of pump. Oil
should be visible one-half way up
sight glass (10-40W non-foaming).
The oil level can also be checked
by using the dipstick on the top of
the pump.

STEP 2:

Attach high pressure hose

to discharge nipple using quick
coupler. Lock coupler securely into
place by pulling back coupler collar
and inserting it onto discharge
nipple, then pushing collar forward
to lock in place.

NOTE: If using detergent injector,
attach detergent injector to
discharge nipple using quick
coupler. Attach high pressure
hose to other end of detergent
injector.

STEP 5:

Fill gasoline tank and

check engine oil.

Fill diesel tank with diesel fuel.

STEP 3:

Attach wand to spray gun

using teflon tape on threads to
prevent leakage. Attach swivel
connector on discharge hose to
spray gun using teflon tape on
threads. Attach swivel connector on
high pressure hose to spray gun
using teflon tape on threads.
Engage safety latch to prevent from
triggering gun.

STEP 6:

On electric start models,

you will need to install a battery
making sure that the red cable is
attached to the positive terminal.
Use a Group U1 garden tractor
style type of battery rated for 300
CCA (battery not included).

NOTE: Battery is required for
burner to operate.

CAUTION: These machines are
intended to be protected from
outside environments.
Attention : Ces machines sont
destinées à être protégées des
environnements extérieurs.
CAUTION: Risk of injury. Discon-
nect battery ground terminal
before servicing.
ATTENTION : Risque de blessure.
Débranchez la borne de masse de
la batterie avant l'entretien.

Karcher HDS 3.5/40 GE MT Operator’s Manual 9.807-942.0 -

C

Inlet

Connector

High Pressure

Hose

Discharge

Nipple

Detergent
Hose

Detergent

Injector

(Option)

Dipstick

Gasoline

Tank

POS

NEG

Red

Black

Diesel Fuel

Tank

Safety

Latch

.

CAUTION: Do not confuse diesel

fuel and gasoline when filling tanks.
Keep proper fuel in proper tanks.
ATTENTION: Ne pas confondre du
carburant diesel et l'essence au
moment de remplir les réservoirs.
Garder le carburant approprié dans
des réservoirs appropriés.

NOTE:

Diesel Fuel Shut-off must be in the ON position prior to turning on

burner.

«
...
15
16
17
18
19
...
»

Содержание Trailer HDS Series

































Отзывы:

Нет отзывов