Kärcher LB 930/36 Bp, Руководство пользователя

Страница: 12 / 158

12 English
Control elements
The leaf blower has the following control elements:
● A power switch for switching the device on and off.
The speed is regulated via the power switch, de-
pending on how strongly it is pressed.
● A lever for fixing the speed to set the speed of the air
flow.
● A turbo boost button to maximise the air speed that
has been set via the speed fixing function.
Inserting the battery pack
ATTENTION
Dirty contacts
Damage to the device and battery
Check the battery mount and the contacts for soiling
and clean them as necessary before inserting the bat-
tery.
Illustration D
1. Push the battery into the mounting in the device until
it audibly latches into place.
Switching on the device
몇
CAUTION
Risk of injury from flying parts and hearing damage
due to noise
Always wear eye and hearing protection.
1. Insert the battery pack, see chapter Inserting the
battery pack .
2. Press the trigger.
Illustration E
3. Fix the speed.
Illustration F
a Use the speed fixing function to adjust the
amount of airflow.
b If necessary, press the turbo boost button for
maximum flow speed.
Changing nozzles
1. Remove the nozzle.
Illustration G
a Turn the bayonet lock until the nozzle can be re-
moved.
b Remove the nozzle
2. Mount the new nozzle.
a Slide the cutouts on the nozzle over the lugs on
the blower pipe.
Illustration B
b Turn the nozzle so that the two arrows point to-
wards each other.
The nozzle is latched in position.
Removing the battery pack
Note
During longer work breaks, remove the battery pack
from the device and secure it against unauthorised use.
1. Pull the battery pack unlocking button in the direc-
tion of the battery pack.
Illustration H
2. Press the battery pack unlocking button to unlock
the battery pack.
3. Remove the battery pack from the device.
Finishing operation
1. Remove the battery pack from the device (see
Chapter Removing the battery pack ).
2. Clean the device (see Chapter Cleaning the de-
vice ).
Transport and storage
1. Switch off the device.
2. Remove the battery pack, see Chapter
Removing
the battery pack .
3. Removing the blower pipe nozzle.
Illustration G
a Turn the blower pipe nozzle until it can be re-
leased from the blower pipe.
b Remove the blower pipe nozzle.
Care and service
The device is maintenance-free.
Cleaning the device
몇 WARNING
Uncontrolled startup
Risk of injury
Remove the battery pack from the device during work
breaks and before carrying out any service or care work.
ATTENTION
Incorrect cleaning
Damage to the device
Clean the device with a damp cloth.
Do not use solvent-based cleaning agents.
Do not immerse the device in water.
Do not clean the device with a hose or high-pressure
water jet.
1. Switch off the device.
2. Remove the battery pack (see chapter
Removing
the battery pack ).
3. Clean the exterior of the device with a soft, dry cloth
or with a brush.
Illustration I
Troubleshooting guide
Malfunctions often have simple causes that you can
remedy yourself using the following overview. When in
doubt, or in the case of malfunctions not mentioned
here, please contact your authorised Customer Service. As the battery pack ages, even if it is looked after, its ca-
pacity reduces such that the full run time will no longer
be reached when fully charged. This does not indicate a
defect.
Fault Cause Rectification
The device does not start
up Battery pack is not inserted correctly.  Push the battery pack into the mounting
until it latches into place.
Battery pack is empty  Charge the battery pack.
Battery pack is defective.  Replace the battery pack.
The device stops during
operation The battery has overheated  Stop working and allow the battery to cool
down to normal battery temperature.
Motor has overheated  Stop working and allow the motor to cool
down.