background image

6

WORKING WITH DETERGENT

Karcher Pressure washers operate at two pressures. The high pressure setting is used for
cleaning, you cannot apply detergents when working at high pressure. To apply detergents you
must be operating at low pressure.

Caution

Never use:

• Bleach, Chlorine products and other 
corrosive chemicals
• Liquids containing solvents 

(i.e., paint thinners, gasoline, oils)

• Tri-sodium phosphate products
• Ammonia products
• Acid-based products
These chemicals will harm the unit and
will damage the surface being cleaned.

Step 2

Fill a container with Karcher

detergent. Place the filter end of detergent
suction tube into the container.

Step 3

Turn on the pressure washer.

Pull trigger to operate unit: Liquid detergent
is drawn into the unit and mixed with water.
Apply detergent to work area. Do not allow
detergent to dry on surface.

For best results see Cleaning Tips
on pages 8 & 9 for specific informa-
tion on how to clean 
different surfaces.

Always Use Karcher 
Detergents for Best Results.

Karcher biodegradable detergents are
specially formulated to protect the environ-
ment and your pressure washer. The special 
formula won’t clog the suction tube filter 
and will protect the internal parts of the pres-
sure washer for a longer life. For Karcher
Detergents, check your retailer 
or call:

The following Karcher detergents are 
available:

• Vehicle Wash

• House Wash

• Degreaser

• Deck Wash

• All Purpose Cleaner

In USA Call:

1-800-537-4129

or visit our website:

www.karcher-usa.com

Step 1

Install the Wash brush or the

Vario spray wand. Set the Vario spray wand
to the low pressure setting (-) by turning the
wand collar. The wand must be set in the low
pressure (-) position to apply detergents.

Содержание K360 M













Отзывы: