English
13
1
Push handle
2
Filter key
3
Hose/cable holder
4
Filter venting screw
5
Operating hours counter
6
High-pressure connection (Classic version)
7
Water shortage safeguard
8
Advance pressure pump venting screw (option)
9
Accessory compartment
10
Pressure gauge
11
Safety valve
12
Thermostat valve
13
High-pressure connection (Advanced version)
14
Type plate
15
Parking brake pedal
16
Filter
17
Mains connection cable with mains plug
18
Water connection
19
Power switch
20
Water shortage indicator lamp
21
Operating state indicator lamp
22
Oil drain plug
23
Oil level display
24
Oil filler neck
25
Venting lever
26
Advance pressure pump (option)
27
Spray lance storage
28
Lashing eyelet
Attachment point for catching fixture
29
Crane loading brace
30
High-pressure gun storage compartment
31
Bypass pipe (dump gun, Classic version)
32
Spray lance
33
High-pressure nozzle
34
Union nut
35
Trigger
36
Safety latch
37
High-pressure gun (dry shut, Adv version)
38
High-pressure gun (dump gun, Classic version)
Installation
Fitting the venting screw
1. Unscrew the transport screw.
2. Screw in and tighten the venting screw supplied.
60 Hz version
1. On 60 Hz version devices, attach a suitable mains
plug to the mains cable. The mains plug may only be
attached by a qualified electrician.
Check the oil level
1. Position the device on a level surface.
2. The oil level must be in the middle of the oil level dis-
play.
3. Top up with oil if necessary (see "Technical data")
Maximum pressure screw connection
This system establishes the connection between the
spray lance and high-pressure gun and also between
the spray lance and nozzle.
1. Screw the pressure ring far enough onto the spray
lance or hose connection so that approximately 2
thread turns are visible before the pressure ring.
Note: The pressure ring has a left-hand thread.
1
High-pressure connection
2
2 thread turns visible
3
Pressure ring, left-hand thread
4
Pressure screw
5
Spray lance
2. Fit the spray lance with pressure piece into the high-
pressure connection.
3. Push the pressure screw onto the pressure ring.
4. Screw in and tighten the pressure screw (tightening
torque 160 Nm).
Installing accessories
Install accessories only when the device is switched off.
Do not exceed the maximum tightening torque of 20 Nm
when tightening the screw connections.
1. Connect the spray lance to the high-pressure gun.
2. Connect the high-pressure hose to the high-pres-
sure gun. Maximum hose length 40 m, DN 6.
3. Connect the high-pressure hose to the high-pres-
sure connection.
4. Fit the nozzle holder onto the spray lance.
5. Insert the nozzle into the nozzle holder.
6. Screw on the union nut and hand-tighten.
High-pressure hose catching fixture
1. Secure the high-pressure hose on the high-pressure
gun.
1
2
3
4
5
Содержание HD 9/100-4 Cage Classic
