Kärcher Cuda 4860 Series Скачать руководство пользователя страница 23

Страница: 23 / 56

Maintenance

Reach into the drive pulley access hole with your
fingers to remove the chain from the drive
sprocket. Take care not to let the chain slip into the
wash chamber. Use a piece of wire to secure the
chain while you replace the motor.

Disconnect all power leads from the motor, taking
care to mark them for reassembly.

Raise the motor and bracket to remove the
assembly from the pivot pin.

10. Use a 1/8” hex key to remove the pulley and steam

shield disk from the drive motor shaft, then remove
the 1/2” bolts holding the motor to the mounting
bracket.

11. Install the new motor. Installation is the reverse of

removal.

12. Reconnect the drive chain to the turntable.

Timers and Switches on the Control Panel
Required Tools and Equipment

•

5/16" wrench or socket

•

1/2" wrench or deep socket

•

small phillips-head screwdriver

•

small flat-head screwdriver

Replacement Procedure

Disconnect power to the machine.

Remove control panel face plate (four 5/16”
screws).

Disconnect the wiring harness from the rear of the
face plate.

Remove the knob from the timer you wish to
remove.

Remove the two screws, retaining nut, and o-ring

that hold the timer switch to the control panel.

Detach the power leads from the timer.

Attach the power leads to the new timer.

Install the new timer. Installation is the reverse of
removal.

Cuda 4860 Operator’s Manual 8.914-383.0 - U

Wire to

Secure Chain

Drive

Chain

Move Motor

Assy. Forward

to Loosen

Chain

Steam
Shield

Disk

Hex

Bolt

Mounting

Screws

Retaining

Nuts

Screws

All manuals and user guides at all-guides.com

Содержание Cuda 4860 Series

























































Результаты поиска

Содержание Cuda 4860 Series

Отзывы:

Похожие инструкции для Cuda 4860 Series

Бренды по названию

Популярные бренды

Kärcher Cuda 4860 Series, Руководство оператора

Результаты поиска

Содержание Cuda 4860 Series

Отзывы:

Похожие инструкции для Cuda 4860 Series

Бренды по названию

Популярные бренды