manualshive.com logo in svg

KANSAI SPECIAL LX-SP Series, Инструкция по эксплуатации

Поделиться
Скачать
KANSAI SPECIAL LX-SP Series Скачать руководство пользователя страница 2

 

Ｌ

Ｌ

Ｘ

Ｘ

-

-

Ｓ

Ｓ

Ｐ

Ｐ

 

 

s

s

e

e

r

r

i

i

e

e

s

s

 

 
 

INTRODUCTION 

 
 

Thank you for your purchasing Kansai Special’s LX-SP Series. 
Read and study this instruction manual carefully before beginning any 
procedures and save it for later use.

 

 
 

1.

 

This instruction manual describes setting-up and adjustment procedures for this 

machine. 

2.

 

Before operating the machine, make sure the pulley cover, safety cover, etc. are 

secured. 

3.

 

Before adjusting, cleaning, threading the machine or replacing the needle, be sure to 

turn off the power. 

4.

 

Please do not start the machine with no oil in the reservoir. 

5.

 

Refer to the parts list as well as this instruction manual before maintenance. 

6.

 

The contents described in this instruction manual are subject to change without 

notice. 

 
 

  I n d i c a t i o n   o f   s e r i a l   n u m b e r    

 
 
 
 
 
 
 
 
 
 

 
 
 

Model 

Zip code 

0 6 0 0 0 0 1 

The year of manufacture

 

Serial number

 

 

Содержание LX-SP Series


















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды