PLEASE NOTE:
EVOD Twist batteries are lockable and are frequently shipped in the "locked" state. Being
able to lock a battery is an important safety feature that allows you to carry an assembled e cigarette in
your pocket or purse without having to fear that it will turn on accidentally.
You can lock or unlock an EVOD Twist battery by pressing the button rapidly 5-7 times. When you do that,
the battery will flash several times, indicating that you have either locked or unlocked it. If the button on
your Twist battery does not light up when you press it, the battery is probably locked and you will need to
unlock it. If your battery does not flash after rapidly pressing the button 5-7 times, you probably are not
pressing the button fast enough or it is a completely uncharged battery. It is easy to tell if an e cigarette
battery is not charged; the light on the charger will turn red when the battery is screwed into it.
Assembling Your Twist-T3S Electronic Cigarette
Twist-T3S electronic cigarettes have four pieces but they come with the clearomizer assembled, so it looks
like there are only two pieces:
1. EVOD Twist Battery: It is the longest piece and has a recessed button on it.
2.
It is tube-shaped, glass-like and translucent, approximately 3 inches long and has a
mouthpiece attached to it.
3. Metal Clearomizer Base: It is about 3/8 inch long and is the only piece that can screw into the outer threads
of the SMOK Winder battery. The other end also has screw threads and is what the T3S coil screws into.
4.
Approximately an inch long, it is a thin, pointy looking metal piece with rubber gaskets on it. The
base of it screws into the the metal clearomizer base and the thin pointy side slides into the clearomizer
tube.
Assembling a Twist-T3S Starter Kit is pretty easy. Here's all you need to do:
1. The T3S Clearomizer comes already assembled with your kit. Hold onto the metal clearomizer base and
unscrew the clearomizer tube from the metal base. The Coil, which is screwed into the Clearomizer Base
will stay attached to the base. Please make sure the coil is screwed onto the metal base tightly. Frequently,
the manufacturer screws them on very loosely, which could result in improper contact with the battery or
cause the clearomizer to leak.
2.
Holding the clearomizer tube with the mouthpiece end facing down, fill the clearomizer tube by squirting
down the inner sides. This is more easily done by tilting the clearomizer tube at about a 45 degree
angle. Be careful not to get any e-liquid into the inner part of the tube and also be sure to not fill it all the
way. The e-liquid MUST stay below the inner tube part of the clearomizer tube.
NOTE:
The easiest way of doing this is with a needle tip bottle which is why we have included an empty
one with your kit. You can fill the
with the e-liquid of your choice.
3. While still holding the clearomizer tube, mouthpiece side down, screw the clearomizer base and coil back
onto the clearomizer tube securely. The coil will slide into the inner part of the tube. DO NOT cross-thread
while you are screwing the pieces together.
4. Screw the filled, assembled T3S clearomizer onto your Twist battery.
Your Twist-T3S is now assembled and ready for use!
TIP:
There are three holes in the metal clearomizer base that allow air to circulate through the clearomizer.
If you notice that it is harder to draw on your Twist-T3S or that you are not getting as much vapor as you
used to, the airflow holes may be blocked on your clearomizer base. Take a safety pin and poke it into each
of the three holes to clear them.
Using Your Twist-T3S E-Cigarette
IMPORTANT:
You should always take five drags from your e-cigarette without pressing the button when
using a new atomizer coil in order to prime it. After taking the five "dry" puffs, you can press the button and
use your e-cigarette.
