background image

INTRODUCTION 

 

This Manual describes the operation for the Kanematsu Land mobile radio 

 

This Land Mobile is full-featured FM transceiver designed for flexible mobile and base station 

business communications in the VHF or UHF Land mobile bands. 
 

This Land mobile radio can be programmed with 128 channels. This Land mobile include a 16 
segment, 8character, numeric display for channel display.     

      Important channel frequency data is stored in EEPROM and flash memory on the CPU, 
and easily programmable by dealers using personal computer and PC EDITER software. 
 

 

FCC Requirements 

Your radio must be properly licensed Federal Communications Commission prior to use. Your 
Wireless dealer can assist you in meeting these requirements. Your dealer will program each 

radio with your authorized frequencies, signaling codes, etc., and will be there to meet your 
communications needs as your system expands. 

 

 

SAFETY

  

WANING

 

INFORMATION

 

 

  
    READ THIS IMPORTANT INFORMATION ON SAFE AND EFFICIENT OPERATION 

BEFORE USING 

 

YOUR

 

LAND

 

MOBILE

 

RADIO 

 

・ 

Only qualified technicians are allowed to repair this product. 

・ 

Do not operate the radio without a proper antenna attached. As this may damage the 
radio and may also cause to exceed FCC RF exposure limits. 

・ 

Typical electronic systems that may malfunction due to the lack of protection from radio 
frequency energy present when transmitting. If the vehicle contains such equipment, 
consult the dealer. 

・ 

Just as it is dangerous to fuel a vehicle with motor running, similar hazard exist when 
operation a mobile radio. Be sure to turn the radio off while fueling a vehicle. 

・ 

Do not operate the radio without a proper antenna attached, as this may damage the 
radio and may also cause you to exceed FCC RF exposure limits. 

・ 

Do not transmit for more than 50% of total radio use time. Transmitting more than 50% 
of the time can cause FCC RF exposure compliance requirements to be exceeded. 

・ 

Always Keep at least 25cm (10inches) between the antenna and  operator while 
transmitting. 

・ 

Always use authorized accessories.  

・ 

Dynamite blasting caps may be caused to explode by operating a radio within 500 feet 
of the blasting caps. Always obey the “Turn Off Two –Way radios” signs posted where 

dynamite is being used. 

Содержание F-25U












Отзывы: