SETUP INSTRUCTIONS
11930 Orchestra music stand
»Overture«
INTENDED USE
Stackable orchestra music stand in modern look, especially designed for
schools, halls and concert halls
FEATURES & CAPABILITIES
- Stepless height adjustment from 760-1300 mm by means of clamping lever -
-
fast and uncomplicated
- The tension of the lever can be individually adjusted as desired
- Steplessly inclinable music desk
- Integrated, impact sound absorbing parquet flooring protectors
- Space-saving stacking - spacing only 70 mm - thanks to special foot design
- Optionally available: Wagon 11934 for transport and storage up to
-
12 orchestra music stands
- Large music desk: 500 x 320 x 56 mm; weight 3.5 kg
SAFETY NOTES
Thank you for choosing this product. Please read and follow these instructions carefully. It
informs you about all important steps necessary for safe installation and operation. We
recommend that you keep them for future reference.
1. COMPONENTS
Visually check whether all parts are present and in good
order as far as can be seen.
a
Tripod with base
e
Accessories for desk mounting:
b
Tube combination cpl.
e.1
Joint half shell (2x)
b.1
Base tube slots
e.2
Rubber washer ø 30 mm (2x)
b.2
Clamping lever
e.3
Washer with square hole
b.3
Extension tube
e.4
Washer ø 8,5 mm
c
Accessories for base mounting:
e.5
Carriage bolt M8 x 50 mm
c.1
Allen screw M5 x 16 mm
e.6
Locking nut M8
c.2
Threaded plate M5
e.7
Protective cap for M8
c.3
Allen key SW4
e.8
Wrench SW8/13
d
Music desk
2. MOUNTING the PLATE to the EXTENSION TUBE
- Be sure that the surface is suitable and level
- Place the load gently and align it centrally
- The tight fit or mobility of the extension tube and music
-
desk can be adjusted individually
- Due to the moving parts there is a risk that the user can
-
pinch or wedge their hands: Careful and attentive handling
-
during setup, operation, and disassembly is indispensable.
3. MOUNTING the BASE to the BASE TUBE
3.1
PREPAR the TUBE COMBINATION
b
3.1.1
Lay the desk flat on a table and set up the tube
3.1.1
combination vertically.
3.1.2
Open clamping lever
b.2
.
3.1.3
Pull out the base tube slightly until the two
3.1.3
slots
b.1
are no longer covered by the inner tube.
3.1.3
Then close the clamping lever again.
3.2
PLACING the THREADED PLATE
c.2
3.2.1
Insert the plate into the slot of the base tube.
3.2.2
Screw the Allen screw
c.1
into the plate a little by
3.2.2
hand.
3.2.3
Lift the screw head and insert the plate into the slot opposite
3.2.3
until it no longer protrudes above the base tube.
3.2.4
Hold plate in position and unscrew Allen screw again.
2.1
Place music desk
d
on the floor or table so that the rear
2.1
side is facing upwards.
2.2
Loosen the clamping lever
b.2
and pull the extension
2.2
tube
b.3
a little bit out of the base tube.
2.3
Place joint half shells
e.1
onto the tube end
b.3
.
2.3
The pins engage in the holes.
2.4
Press rubber washers
e.2
into the recesses of the
2.4
joint half shells and…
2.5
…slide this ensemble between the two support brackets
2.5
at the back of the music desk until the holes of all parts
2.5
are aligned.
2.6
Slide washer with square hole
e.3
over carriage bolt
e.5
2.6
and guide through the hole of the support brackets.
2.7
Slide washer
e.4
over the thread and screw on lock nut
2.7
M8
e.6
.
2.7
Use wrench SW13
e.8
for this purpose.
2.8
Finally, press on protective cap
e.7
.
KÖNIG & MEYER
GmbH & Co. KG
Kiesweg 2, 97877 Wertheim, www.k-m.de
11930-000-55 Rev.23 03-79-179-00 8/22
1. COMPONENTS
2. MOUNTING the PLATE to the EXTENSION TUBE
3. MOUNTING the BASE to the BASE TUBE
