18820 Table-style keyboard stand
»Omega Pro«
- a slim yet high-strength tubular steel construction
- uncomplicated, graduated height adjustment
- individually positionable support arms – according to width of keyboard
- foldable legs for flat packaging - ideal for mobile use
- design matches keyboard benches 14080, 14085 and 14086
- optional attachments 18811 (2nd level) and 18822 (3rd level) are available
- for more mounting options see chapter: TECHNICAL DATA
- max. load: 80 kg including additions
- base w x d 975 x 575 mm, height 600-1020 mm,
-
supports w x d max. 790 x 345 mm
SAFETY INSTRUCTIONS
1. COMPONENTS
2. ASSEMBLY and HANDLING
Thank you for choosing this product. This instruction manual informs you about the
important steps to set up and handle the product. We recommend to keep the manual
in a separate place for a possible later use.
GENERAL
- The possibility to adjust the product involves entrapment hazards. Therefore careful
-
and thoughtful handling during installation, operation, dismantling and maintenance
-
is essential.
- Protect the stand from adverse external conditions (moisture, wind, shocks).
- The careful and diligent treatment preserves the functionality,
-
durability and ensures last not least safety.
- Faulty products are not to be used; damaged parts must be replaced or repaired
-
before handling
OPERATION
- Maximum load 80 kg (including additions)
- Ensure that the subsurfaces are stable and even
- The locking bolt of both clamping screws must always be engaged
- Always remove the keyboards before you adjust the height
- The maximum height is reached as soon as the STOP mark on the stand tube
-
becomes visible (see chapter 3. HEIGHT ADJUSTMENT)
- both tubes must always be adjusted to the same height
- The long side of the supports must point in the direction of the long base sides
- Screw connections must be firmly tightened
SET-UP INSTRUCTIONS
1. COMPONENTS
Please carry out a visual inspection to ensure that all parts are complete and in
good as order far as can be seen.
a
U-bracket, foldable,
b
base frame (2x),
c
support arm (2x),
n
carrying strap
Accessories bag:
d
Velcro
e
rubber pads ø 20 mm (4x),
f
carriage bolt M6 x 65 mm (2x),
g
washer ø 6,4 mm (2x),
h
wing nut M6 (2x),
i
cable clamp (4x),
k
spring-loaded clamping knob without logo (2x),
m
spring-loaded clamping knob with logo (2x),
2. ASSEMBLY and HANDLING
STAND (2.1-2.4)
2.1
Unfold both stand tubes of the u-bracket
a
all the way to the stop.
WARNING! During this procedure there is entrapment hazard in area
Q
.
It is therefore essential that you keep your limbs, clothing and other things
out of the area. This also applies to third parties.
2.2
Screw the spring-loaded clamping knobs
m
into the threaded bushings of the upper corners
2.2
and make sure that the locking bolts are immersed in the boreholes of the stand tubes.
2.3
Insert the base frame
b
into the stand tubes...
2.4
...and by screwing the spring-loaded clamping knobs
k
fix their (equal) height.
SUPPORT ARMS c
2.5
We recommend symmetrical mounting of the two support arms.
2.6
The long side of the support must point in direction of the long base tube.
2.7
Insert carriage bolt
f
through the support
c
and the desired borehole of
2.7
the u-bracket and screw together with washer
g
and wing nut
h
.
RUBBER PADS d
2.8
They are self-adhesive and can when needed be placed
c
on the desired position of
2.8
the support - e.g. when the instrument touches down between the two large rubber
2.8
protectors because the depth is too small.
CABLE CLAMPS e
2.9
They keep the wiring in order.
2.9
They can be positioned anywhere on the U-bracket
b
.
2.10
Procedure: Position the opening of the clamp slightly diagonally on the tube,
2.10
press until both brackets open, enclose the tube and audibly snap-in.
2.11
The cable clamps can be moved on the U-bracket.
ADJUSTMENT PLATE for FLOOR LEVELING
2.12
To compensate for uneven floors, the two front parquet protectors have adjustment
2.12
plates (ribbed surface), which can be turned out up to approx. 7 mm if necessary.
VELCRO
2.13
The Velcro strap is used to secure the folded foot tubes.
CARRYING STRAP n
2.14
It is a welcome help when transporting the keyboard table. For this purpose:
2.14
Place the keyboard table on the support arms
c
- fold the legs and hook in both
2.14
Karabiners into the boreholes (
A
or
B
)
FOLDING FUNCTION and TRANSPORT
Turn the keyboard table over and place it on the support arms
c
2.15
Loosen tightened spring-loaded clamping knob
m
approx. one turn
2.16
Pull handle (= unlock bolt) and hold, now retract base.
2.17
RECURRING UNFOLDING: first remove the CARRYING STRAP
2.14
and the
2.17
VELTRO STRIP
2.13
; afterwards pull and hold handle
m
, swing open the legs (90°),
2.17
screw in spring-loaded clamping knob
m
.
2.13
The unfolding of the legs
during transport is preven-
ted by securing them with
the firm tightening of the
Velcro around both base
frames.
2.17
NOTE:
The thread of the spring-
loaded clamping knob
m
must not protrude in the
inside of the pipe.
Otherwise the foot does
not fully unfold. In this
case turn back the spring-
loaded clamping knob as
far as necessary.