Kanardia miniDaqu Скачать руководство пользователя страница 40 | Manualshive

Страница: 40 / 53

Kanardia miniDaqu Скачать руководство пользователя страница 40

9.3

Voltage

miniDaqu — Manual

Absolute sensor option is available since software version 3.7.

When compared to vented gage sensor, the only difference is in the

Function

settings. Table 11 shows the configuration.

Table 11:

Rotax iS engine with absolute fuel pressure sensor.

Option

Selection/Setting

Channel

Any E or F

Function

Fuel P. cmp abs

Sensor

Active 0.5-4.5 V

Report time

0.5 – 1.0 s

Filter

2.0 s

Max value (at 4.5 V)

10

Note that

Fuel P. cmp abs

is used for the function. This abbreviation stands

for

Fuel Pressure Compensated, Absolute

. The fuel pressure is difference be-

tween the absolute fuel pressure detected on the rail

S

and manifold pressure

M

. The indicated fuel pressure

F

is then calculated as:

F

=

S

−

M

9.3

Voltage

Daqu can measure voltages from 0 to +30 V DC on the channel C. The system
voltage is usually measured on this channel.

Some engines, Rotax iS, for example, transmit their own system voltage, which
is obtained from engine ECU. When a voltage is connected and activated on
Daqu C channel, this voltage will override the voltage transmitted by ECU.

9.3.1

Installation

This connection does not power Daqu. Daqu gets power via CAN bus cable.
Daqu will work properly even when system voltage is not connected to the C
channel.

Since system bus may provide significant power, it is very important to install
an inline protection fuse on the wire that connects positive terminal of the C
channel with the system bus. The fuse shall be close to the system bus. The
fuse protects from shortcuts due to accidental slip of the wire. The measuring

©

Kanardia

2019-2022

38

«
...
38
39
40
41
42
...
»

Содержание miniDaqu






















































Отзывы:

Нет отзывов