Using Your Kambrook Jaguar
Vacuum Cleaner
Remove all packaging from the unit, hose
and other accessories; ensure that you
have removed all of the accessories before
discarding the packaging.
Ensure that the dust bag and filters are
correctly fitted.
Locate the crush proof hose and push the
connection point into the hose inlet
connection on the top of the unit, until a
“click” sound is heard.
Connect the wide end of the metal wand
to the hose end, and push together firmly.
Fit the floor tool to the narrow end of
the wand/s and push together firmly.
Fully extend the power cord by pulling
the power plug (situated at the rear of the
unit) out from the unit, until the
red/yellow tape on the cord is shown.
ENSURE THAT YOU DO NOT
OVER EXTEND THE POWER
CORD – DO NOT EXTEND PAST
THE RED/YELLOW WARNING
TAPE ON THE CORD
Plug into a 230/240v power point and
switch the power on.
To commence vacuuming push down on
the on/off foot pedal, at the top, rear of
the unit.
When vacuuming is complete, push down
on the ‘on/off’ pedal to switch off.Turn
the power off at the outlet and then
remove the power cord from the power
outlet (when removing plug from the
power outlet grasp the plug not the cord).
To retract the cord push down on the
‘cord rewind’ pedal.
IMPORTANT: HOLD THE PLUG
END WHEN RETRACTING THE
CORD TO PREVENT IT FROM
STRIKING YOU OR THE VACUUM.
ALWAYS ENSURE THAT THE
DUST BAG AND THE MOTOR
PROTECTION FILTER ARE
CORRECTLY FITTED. NEVER
OPERATE WITHOUT THE DUST
BAG OR FILTERS IN PLACE.
Crevice and brush tool accessories
The crevice tool is ideal for vacuuming
hard to reach places such as the edges
along skirting boards, crevices, corners
and in between cushions.
The brush tool can be used to vacuum
delicate surfaces and areas such as shelves
venetian blinds, furniture & lampshades.
Separate crevice and brush tools are
located inside the on-board tool storage
compartment.The opening for this
compartment is located directly below the
hose connection inlet.To open place a
finger inside the thumb groove and pull
the compartment lid upwards.
Turn off the vacuum cleaner when
changing any attachments.
Dust bag indicator and changing the
dust bag
The dust bag should be emptied when full.
The dust bag indicator window will
gradually turn red as the bag fills up and
when the dust bag indicator displays ‘red’
it is time to change the dust bag.
4
Always switch appliance off, then switch
off at the power outlet and unplug the
appliance prior to replacing dust bags or
filters.
To remove the dust bag, ensure the unit is
down on its wheels, remove the crush
proof hose and push the ‘Dust bag
compartment lid release lever’ Once the
lid has released, pull the top cover back.
To remove the bag, grasp the plastic insert
attached to the dust bag and pull upwards
as per arrow indicator.
To empty the bag, remove the plastic bar
attachment at the bottom of the bag by
sliding across. Once the bag has been
emptied, replace the sliding bar and your
bag is ready to re-use.
When vacuuming fine dust particles, the
fine dust particles can clog the pores of
the dust bag and the dust bag indicator
will indicate full. If this happens the bag
could appear relatively empty, however
the bag will still need to be emptied to
avoid strain on the motor.
NOTE:The bag compartment lid may not close if
the bag is not correctly fitted.
IMPORTANT: DO NOT USE
THE UNIT WITHOUT A DUST
BAG IN PLACE
Replacing filters
Filters must be cleaned from time to time
to remove the fine dust particles that have
been collected.This can be done by
shaking them, however after
approximately 8 dustbag changes the
filters should be replaced.
Motor protection filter
The motor protection filter must always
be in place when operating the vacuum
otherwise damage to the motor may
occur
To replace the motor protection filter –
Remove the dustbag or pull the bag
forward.The motor protection filter is
located at the rear, right hand side of this
inner chamber. Pull the plastic filter holder
upward to remove.
5
Dust bag holder
Filter holder
Filter holder
Removable filter
