Kaisai KHC-22RY3, Инструкция по установке

Страница: 47 / 80

41
1.The environment temperature curves of the low temperature setting for heating mode and ECO heating mode
2.The environment temperature curves of the high temperature setting for heating mode and ECO heating mode
10 START-UP AND CONFIGURATION
The unit should be configured by the installer to match the installation environment (outdoor climate, installed options, etc.) and
user expertise.
It is important that all information in this chapter is read sequentially by the installer and that the system is configured
as applicable.
CAUTION
10.1 Climate related curves
The Climate related curves can be selected in the user interface. Once the curve is selected, the target outlet temperature. In
each mode, user can select one curve from curves in the user interface(curve can’t be selected if dual room thermostat function
is enabled.
It’s possible to select curves even dual room thermostat function is enabled.
The relationship between outdoor temperature (T4/°C) and the target water temperature(T1S/°C) is described in the table and
picture in the next page. )
T4 ≤ -20 -19 -18 -17 -16 -15 -14 -13 -12 -11 -10 -9 -8 -7 -6 -5 -4 -3 -2 -1 0
1-T1S 38 38 38 38 38 37 37 37 37 37 37 36 36 36 36 36 36 35 35 35 35
2-T1S 37 37 37 37 37 36 36 36 36 36 36 35 35 35 35 35 35 34 34 34 34
3-T1S 36 36 36 35 35 35 35 35 35 34 34 34 34 34 34 33 33 33 33 33 33
4-T1S 35 35 35 34 34 34 34 34 34 33 33 33 33 33 33 32 32 32 32 32 32
5-T1S 34 34 34 33 33 33 33 33 33 32 32 32 32 32 32 31 31 31 31 31 31
6-T1S 32 32 32 32 31 31 31 31 31 31 31 31 30 30 30 30 30 30 30 30 29
7-T1S 31 31 31 31 30 30 30 30 30 30 30 30 29 29 29 29 29 29 29 29 28
8-T1S 29 29 29 29 28 28 28 28 28 28 28 28 27 27 27 27 27 27 27 27 26
T4 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 ≥ 20
1-T1S 35 35 34 34 34 34 34 34 33 33 33 33 33 33 32 32 32 32 32 32 32
2-T1S 34 34 33 33 33 33 33 33 32 32 32 32 32 32 31 31 31 31 31 31 31
3-T1S 32 32 32 32 32 32 31 31 31 31 31 31 30 30 30 30 30 30 29 29 29
4-T1S 31 31 31 31 31 31 30 30 30 30 30 30 29 29 29 29 29 29 28 28 28
5-T1S 30 30 30 30 30 30 29 29 29 29 29 29 28 28 28 28 28 28 27 27 27
6-T1S 29 29 29 29 29 29 28 28 28 28 28 28 27 27 27 27 27 27 26 26 26
7-T1S 28 28 28 28 28 28 27 27 27 27 27 27 26 26 26 26 26 26 25 25 25
8-T1S 26 26 26 26 26 26 26 25 25 25 25 25 25 25 25 24 24 24 24 24 24
T4 ≤ -20 -19 -18 -17 -16 -15 -14 -13 -12 -11 -10 -9 -8 -7 -6 -5 -4 -3 -2 -1 0
1-T1S 55 55 55 55 54 54 54 54 54 54 54 54 53 53 53 53 53 53 53 53 52
2-T1S 53 53 53 53 52 52 52 52 52 52 52 52 51 51 51 51 51 51 51 51 50
3-T1S 52 52 52 52 51 51 51 51 51 51 51 51 50 50 50 50 50 50 50 50 49
4-T1S 50 50 50 50 49 49 49 49 49 49 49 49 48 48 48 48 48 48 48 48 47
5-T1S 48 48 48 48 47 47 47 47 47 47 47 47 46 46 46 46 46 46 46 46 45
6-T1S 45 45 45 45 44 44 44 44 44 44 44 44 43 43 43 43 43 43 43 43 42
7-T1S 43 43 43 43 42 42 42 42 42 42 42 42 41 41 41 41 41 41 41 41 40
8-T1S 40 40 40 40 39 39 39 39 39 39 39 39 38 38 38 38 38 38 38 38 37
T4 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 ≥ 20
1-T1S 52 52 52 52 52 52 52 51 51 51 51 51 51 51 51 50 50 50 50 50 50
2-T1S 50 50 50 50 50 50 50 49 49 49 49 49 49 49
49 48 48 48 48 48 48
3-T1S 49 49 49 49 49 49 49 48 48 48 48 48 48 48 48 47 47 47 47 47 47
4-T1S 47 47 47 47 47 47 47 46 46 46 46 46 46 46 46 45 45 45 45 45 45
5-T1S 45 45 45 45 45 45 45 44 44 44 44 44 44 44 44 43 43 43 43 43 43
6-T1S 42 42 42 42 42 42 42 41 41 41 41 41 41 41 41 40 40 40 40 40 40
7-T1S 40 40 40 40 40 40 40 39 39 39 39 39 39 39 39 38 38 38 38 38 38
8-T1S 37 37 37 37 37 37 37 36 36 36 36 36 36 36 36 35 35 35 35 35 35
42
DIP switch is located on the hydraulic module main control board (see "9.3.1 main control board of hydraulic module") and
allows configuration of additional heating source thermistor installation, the second inner backup heater installation, etc.
10.2.1 Function setting
10.2 DIP switch settings overview
T4H1
T4H2
T1SETH2
T1SETH1
T4
T1S (T1S2)
3.The automatic setting curve for heating mode
The automatic setting curve is the ninth curve,the ninth curve can be set as following:
State:In the setting the wired controller, if T4H2<T4H1, then exchange their value; if T1SETH1<T1SETH2, then exchange
their value.
T4 -10 ≤ T4 ＜ 15 15 ≤ T4 ＜ 22 22 ≤ T4 ＜ 30 30 ≤ T4
1-T1S 16 11 8 5
2-T1S 17 12 9 6
3-T1S 18 13 10 7
4-T1S 19 14 11 8
5-T1S 20 15 12 9
6-T1S 21 16 13 10
7-T1S 22 17 14 11
8-T1S 23 18 15 12
T4 -10 ≤ T4 ＜ 15 15 ≤ T4 ＜ 22 22 ≤ T4 ＜ 30 30 ≤ T4
1-T1S 20 18 17 16
2-T1S 21 19 18 17
3-T1S 22 20 19 17
4-T1S 23 21 19 18
5-T1S 24 21 20 18
6-T1S 24 22 20 19
7-T1S 25 22 21 19
8-T1S 25 23 21 20
4.The environment temperature curves of the low temperature setting for cooling mode
5.The environment temperature curves of the high temperature setting for cooling mode
T4C1
T4C2
T1SETC2
T1SETC1
T4
T1S (T1S2)
6.The automatic setting curve for cooling mode
The automatic setting curve is the ninth curve,the ninth curve can be set as following:
State:In the setting the wired controller, if T4C2<T4C1,then exchange their value; if T1SETC1<T1SETC2, then exchange
their value.
47 46