KAESER M100 Скачать руководство пользователя страница 80 | Manualshive

Страница: 80 / 384

background image

6.4.1 Option rb/rk/rm/rs, rb/rl/rm/rs

Adjusting the towbar height

Fig. 27 Towbar height adjustment

1

Locking lever

2

Split pin

3

Split pin properly inserted

4

Handle

1. Pull out the split pin and unscrew the locking lever to the stop.
2. Adjust the towbar with the handle until it is horizontal with the coupling on the towing vehicle

and parallel to the ground.

The parallel tie bar ensures that the overrun braking mechanism stays horizontal (Fig. 27.

The centre-piece can be moved up to 50° upwards and 10° downwards for height adjustment.

3. Tighten the locking lever:

■ Make sure the teeth in the adjustment joint mesh together.
■ Manually tighten the locking lever.
■ Use a hammer to hit the locking lever to further tighten the lower serrated joint until the

bore and the groove for the splint pin are aligned

4. Insert the splint pin.
5. Check if:

■ the teeth in the adjustment joint are fully engaged.
■ The locking lever is tight.
■ The split pin is correctly inserted to secure the locking lever (see 3 in Fig. 27).

6. Tighten the locking lever again after 30 miles.

The serrated joint will not disengage. The serrations are corroded together.
➤ Free the serrations by jerking the towbar horizontally and vertically.

6.4.2 Changing the towing eye/ball hitch

The towbar can be fitted with various towing eyes or couplings.

6

Installation

6.4

Adjusting the chassis

68

Operator Manual Screw Compressor
M100

No.: 9_6999 23 USE

Option rb/rk/rm/rs,

rb/rl/rm/rs

«
...
78
79
80
81
82
...
»

Содержание M100

































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для M100

Бренд: C-Aire Страницы: 20

TU-FLO 700 COMPRESSOR

Бренд: BENDIX Страницы: 36

Бренд: Draper Страницы: 22

Бренд: All-Power Страницы: 30

Бренд: California Air Tools Страницы: 16

Бренд: Powermate Страницы: 24

Бренд: DK2 Страницы: 52

Бренд: SABROE Страницы: 78

Бренд: Gardner Denver Страницы: 71

Бренд: California Air Tools Страницы: 16

Бренд: Craftsman Страницы: 27

Бренд: Panasonic Страницы: 2

Бренд: SCOPREGA Страницы: 16

Бренд: XTline Страницы: 37

Бренд: MGF Страницы: 16

Бренд: California Air Tools Страницы: 17

Бренд: Proheat Страницы: 90

Бренд: Taurus Страницы: 83

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды