KAESER AIRTOWER 3C Скачать руководство пользователя | Manualshive

Страница: 46 / 124

background image

Fig. 11 Recommended machine placement and dimensions [in]

A

Exhaust fan

B

Exhaust air duct

Z

Air inlet aperture

1.

Ambient temperature too low.

Frozen condensate and highly viscous cooling oil can cause damage when starting the ma‐

chine.
➤ Make sure that the temperature of the machine is at least 37 °F before starting.
➤ Heat the machine room adequately or install an auxiliary heater.

2. Ensure adequate lighting so that all work on the machine can be carried out without danger or

hindrance.

3. Ensure that the indicators can be read without glare and that the controller display cannot be

damaged by direct sunlight (UV radiation).

4. Ensure that all intake and exhaust apertures of the enclosure remain opened.
5. If installed outdoors, the machine must be protected from frost, direct sunlight, dust and rain.

5.2.2 Ensuring the machine room ventilation

Adequate ventilation of the machine room has several tasks:
■ It prevents subatmospheric pressure in the machine room.
■ It evacuates the exhaust heat of the machine and thus ensures the required operating condi‐

tions.

➤ Consult with KAESER if you cannot ensure the conditions for an adequate ventilation of

the machine room.

1. Ensure that the flow volume of fresh air is at least the same as the volume taken by the ma‐

chine and exhaust fan from the machine space.

2. Make sure that the machine and exhaust fan can only operate when the inlet aperture is ac‐

tually open.

3. Keep the inlet and exhaust apertures free of obstructions so that the cooling air can flow freely

through the room.

4. Ensure clean air in order to support the proper functioning of the machine.

5

Installation and Operating Conditions

5.2

Installation conditions

36

Operator Manual Screw Compressor
AIRTOWER 3C–7.5C Tri-Voltage

9_6917 34 USE

«
...
44
45
46
47
48
...
»

Содержание AIRTOWER 3C





























































































































Отзывы:

Нет отзывов

Похожие инструкции для AIRTOWER 3C

POLAR AIR P01PSXXP07V120V208X

Бренд: Eaton Compressor Страницы: 39

Бренд: Pacbrake Страницы: 3

Бренд: Villager Страницы: 141

Бренд: Ingersoll-Rand Страницы: 71

Бренд: Grizzly Страницы: 17

Бренд: Craftsman Страницы: 52

Бренд: GEA Страницы: 30

Бренд: Delta Страницы: 24

Бренд: Delta Страницы: 72

Бренд: Coldex Страницы: 7

Бренд: Toolex Страницы: 8

Бренд: Sparmax Страницы: 32

Бренд: Sound Skulptor Страницы: 12

Бренд: California Air Tools Страницы: 16

Бренд: California Air Tools Страницы: 17

Бренд: California Air Tools Страницы: 17

Бренд: 4tek Страницы: 39

Бренд: 4tek Страницы: 37

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды