K-TRON KSU-II/KCM Скачать руководство пользователя | Manualshive

Страница: 16 / 121

background image

1

Programming Reference

1.2 Calibration

Page 16

Docu-No.: 0590020601-EN Rev. 1.6.0

1.2

Calibration

Use the FF Calibration menu to perform feeder calibration.
If the VOL RATE function is activated in the Service Variable Index,
the volumetric rate will be calculated if a product bulk density is
entered in the PRODUCT CHANGE menu.

1.2.1

Calibration sub-menu

• Section

is for motor driven feeders

• Section

is for vibratory feeders

Parameter

Definition

INIT FF

Initial Feedfactor

Input of the starting feeding factor to determine the motor speed. The
Drive Command is calculated as follows (not for vibratory feeders):

DriveCommand(%) = 100 x (Setpoint/Initial Feedfactor)

The starting feed factor can also be calculated with the command
variable <AUTO F.F. CALIB>. Value of <0> will cause an Feedfactor
Alarm see page

The feeder will not run with a Feedfactor of <0>.

Input range: 0 to 99999

Default: 100 kg/hr

AVG FF

Average Feedfactor

The value shows the estimated mass flow value expected at 100%
drive command and is calculated as (not for vibratory feeders):

AverageFeedfactor = 100 x (Massflow/DriveCommand(%)

Average Feedfactor represents the massflow capacity of the feeder
and is affected by bulk material characteristics and the current
feeder mechanical configuration.

Notes:

• The feeder will not run with a Feedfactor of <0>.

Input range: Display only

Table page 1 of 3

«
...
14
15
16
17
18
...
»

Содержание KSU-II/KCM


























































































































Отзывы:

Нет отзывов

Похожие инструкции для KSU-II/KCM

FPBA-01 PROFIBUS DP

Бренд: ABB Страницы: 2

ControlMaster CM15

Бренд: ABB Страницы: 4

Бренд: VAT Страницы: 29

Бренд: Balboa Instruments Страницы: 19

Бренд: Aalborg Страницы: 128

Бренд: Caen Страницы: 20

Бренд: FASAR ELETTRONICA Страницы: 2

Бренд: Faro Barcelona Страницы: 8

Бренд: Faro Страницы: 3

Бренд: YASKAWA Страницы: 456

Бренд: Hanna Instruments Страницы: 88

Бренд: RADEMACHER Страницы: 48

Бренд: tau Страницы: 9

Бренд: tau Страницы: 8

Бренд: Dantel Страницы: 6

GAMMA VERSUS Series

Бренд: JCM Страницы: 111

767-4804/000-800

Бренд: WAGO Страницы: 80

Бренд: Trane Technologies Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды