K Tool International KTI63517 Скачать руководство пользователя страница 4

KTI63517 4  7/16/14

3.  It should not be necessary to refill or top off the reservoir with hydraulic fluid unless there is an external leak. An external leak  

 

requires immediate repair which  must be performed in a dirt-free environment by qualified hydraulic repair personnel who are  

 

familiar with this equipment.

IMPORTANT:

 In order to prevent seal damage and jack failure, never use alcohol, hydraulic brake fluid or transmission oil in the jack. 

Use hydraulic jack oil, a light turbine oil, Chevron AW ISO 32 or Unocal Unax AW 150.

4.  Every jack owner is responsible for keeping the jack labels clean and readable. Use a mild soap solution to wash external  

 

surfaces of the jack but not any moving hydraulic components. Contact K-Tool International for a replacement label if your jack's  

 

label is unreadable.

5.  Inspect the jack before each use. Do not use the jack if any component is cracked, broken, bent, shows sign of damage or leaks  

 

hydraulic fluid. Do not use the jack if it has loose or missing hardware or components, or is modified in any way. Take corrective  

 

action before using the jack again.

6.  Do not attempt to make any hydraulic repairs unless you are a qualified hydraulic repair person that is familiar with this  

 

equipment. Repairs must be performed by an authorized service center.

TROUBLESHOOTING

PROBLEM: UNIT WILL NOT LIFT RATED LOAD.
ACTION:

 

Purge air from hydraulic system by following procedure under SETUP INSTRUCTIONS.

PROBLEM: UNIT WILL NOT SUSTAIN RATED LOAD OR FEELS "SPONGY" UNDER RATED LOAD.
ACTION:

 

Purge air from hydraulic system as above.

PROBLEM:

 

UNIT WILL NOT LIFT TO FULL HEIGHT.

ACTION:

 

Purge air from hydraulic system as above.

PROBLEM:

 

HANDLE TENDS TO RAISE UP WHILE THE UNIT IS UNDER RATED LOAD.

ACTION:

 

Pump the handle rapidly several times to push oil past ball valves in power unit.

PROBLEM:

 

UNIT STILL DOES NOT OPERATE.

ACTION:

 

 Contact your place of purchase for details on handling warranty.

K-Tool International warrants that all jacks and service-related equipment will be free from defects in material and workmanship for a 
period of 2 years following the original date of purchase. This warranty is extended to the original retail purchaser only. If any jack or 
service-related item proves to be defective during this period, it will be replaced or repaired, at K-Tool International’s option, without 
charge. This warranty does not apply to damage from accident, overload, misuse or abuse, nor does it apply to any equipment which 
has been altered or used with special attachments other than those recommended. This warranty does not cover repairs made by 
anyone who is not a K-Tool International Professional Lifting Equipment Authorized Repair Center.

All HD and XD jacks or service-related equipment will be replaced or repaired at K-Tool International’s option during the 2 year warranty 
period.

During the 2 year warranty period, all alleged defective products must be shipped, freight prepaid, along with proof of date-of-purchase, 
to  your  nearest  K-Tool  International  Professional  Lifting  Equipment  Authorized  Warranty  Center.  Be  certain  to  include  your  name, 
address and phone number along with proof-of-purchase information, and a brief description of the alleged defect. The product will be 
returned to the customer, freight prepaid.

Many alleged defectives may simply be handled by calling your nearest Service Center for parts. See pages 17 - 19 for a listing of 
authorized warranty service centers.

In no event shall K-Tool International be liable for incidental or consequential damages. The liability on any claim for loss or damage 
arising out of the sale, resale or use of a jack or related service equipment, shall in no event exceed the purchase price. SOME STATES 
DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION 
MAY NOT APPLY TO YOU.

THIS  WARRANTY  IS  THE  SOLE  AND  EXCLUSIVE  WARRANTY  PROVIDED  IN  CONNECTION  WITH  THE  SALE  OF  K-TOOL 
INTERNATIONAL  PROFESSIONAL  LIFTING  EQUIPMENT.  ALL  OTHER  WARRANTIES,  INCLUDING  ANY  IMPLIED  WARRANTIES  OF 
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, ARE EXCLUDED.

THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE 
TO STATE.

WARRANTY HANDLING PROCEDURES AND GUIDELINES FOR HD AND xD LIFTING EQUIPMENT

Содержание KTI63517




















Отзывы: