background image

Note : The quality of the duct should  meet the local law and fire prevention  standards

8' aluminum flex duct can  the hood directly  or  6 ' aluminum flex duct connect to

and tight .

Connect the aluminum flex duct to  ductwork, wrap with aluminum tape to make all joints secure

hood body by converter 

STEP 8 : CONNECT ALUMINUM FLEX DUCT AND DUCTWORK

Converter

OR

8'aluminum flex duct

TIP (optional):

 beneath the cabinet and flush with the front of the cabinet.

  since the hood is heavy, a cabinet or a car jack is highly recommended.

Lift the hood up and have it placed below the cabinet. Make sure to center the hood 

                                                                   

STEP 3: PREPARE DUCTWORK & SINGLE OUTLET

Make sure you have a 15amp, 120V, 60Hz, single outlet on the left or right of the duct pipe 

(usually is on ¼ of cabinet width). 

Make sure duct pipe is ready to hook up to the range hood before beginning installation (8” 

diameter duct, and roof or wall cap, depending on where you will be venting your hood)

STEP 5: CREATE ACCESS

Create or cut access opening for electrical wire and hood exhaust under the cabinet

STEP 6: ATTACH THE HOOD

STEP 4: ATTACH 2-INCH WIDE WOOD FILLER STRIPS

For installing under the cabinet with recessed bottom, attach 2-inch wide wood filler strips 

From inside of the hood, use “hex bit extension” 
place 1 ¼” provided screw into each key hole (A) OR 
predrilled-holes (B) and secure to cabinet bottom.   
There are 8 holes (4 keyholes & 4 predrilled-holes) 
available. You can use either key or predrilled-hole 
as long as a minimum of 1 screw at each corner of 
hood body. 

STEP 7A: SECURE THE HOOD TO BOTTOM CABINET

STEP 7A: SECURE THE HOOD TO BOTTOM CABINET

11.

Connect the exhaust on the hood to the ductwork above. Use

6'aluminum flex duct

11.

Содержание K1039








Отзывы: