JVC XV-C3SL Скачать руководство пользователя страница 20

Страница: 20 / 81

XV-C3SL

4.3.3 Adjustment preparation

(1) The mechanism assembly is made in the state from the main body from which is detached referring to the disassembly method.

(2) Three studs are installed in the mechanism assembly respectively.

(3) The servo control board is removed from the mechanism assembly, and puts into the state set up as shown in figure. (Each

wire connected by the servo control board this time leaves the connection maintained.)
Between shaft and hook of mechanism assembly of figure Board is put.

(4) The extension cord is inserted in the connector of the assistance board respectively.

The main board is connected with the servo control board as shown in figure.

Fig.7

Fig.8

4.3.4 Adjustment

(1) Puts into the state to display the jitter value on the FL display referring to "Display of the jitter value".

(2) The adjustment screw under the traverse mechanism is turned with hex wrench, and matches so that the jitter value displayed

on the FL display may become

"maximum"

value.

Fig.9

<POINT>

(1) Turns in the forward or the opposite direction,and

makes to the position where the jitter value is good the
half rotation of adjustment screw a and b(180 degrees)
respectively.

(2) Afterwards, adjustment screw b and c are turned in the

same way, and makes to the best position.

<ATTENTION>

(1) Values to judge whether the jitter is allowable or not is

displayed, instead of actual jitter values.
The displayed values are expressed in hexadecimal
numbers.

(2) As this value is bigger, the jitter is more allowable in this

model.

Содержание XV-C3SL

















































































Результаты поиска

Содержание XV-C3SL

Отзывы:

Похожие инструкции для XV-C3SL

Бренды по названию

Популярные бренды

JVC XV-C3SL, Руководство по обслуживанию

Результаты поиска

Содержание XV-C3SL

Отзывы:

Похожие инструкции для XV-C3SL

Бренды по названию

Популярные бренды