background image

– 20 –

Maintenance

To get the best performance of the unit, keep your discs, tapes, and mechanism clean.

Cassette decks

If the heads, capstan, and pinch roller of the cassette deck
become dirty, the following will occur:
• Impaired sound quality
• Discontinuous sound
• Fading
• Incomplete erasure
• Difficulty in recording

To clean the heads, capstan, and pinch roller

Use a cotton swab moistened with alcohol.

To demagnetize the heads

Turn off the unit, and use a head demagnetizer (available at
electronics and record shops).

Cleaning the unit

Stains on the unit

Should be wiped off with a soft cloth. If the unit is heavily
stained, wipe it with a cloth soaked in water diluted neutral
detergent and wrung well, then wipe clean with a dry cloth.

Since the unit may deteriorate in quality, become
damaged or get its paint peeled off, be careful about the
followings.

– DO NOT wipe it with a hand cloth
– DO NOT wipe it strong
– DO NOT wipe it with thinner of benzine.
– DO NOT apply any volatile substance such as

insecticides to it.

– DO NOT allow any rubber of plastic to remain in contact

with it for a long time.

Handling discs

• Remove the disc from its case by

holding it at the edge while pressing
the center hole lightly.

• Do not touch the shiny surface of the

disc, or bend the disc.

• Put the disc back in its case after use

to prevent warping.

• Be careful not to scratch the surface

of the disc when placing it back in its
case.

• Avoid exposure to direct sunlight,

temperature extremes, and moisture.

To clean the disc

Wipe the disc with a soft cloth in a
straight line from center to edge.

DO NOT use any solvent — such as conventional record
cleaner, spray, thinner, or benzine — to clean the disc.

Handling cassette tapes

• If the tape is loose in its cassette, take

up the slack by inserting a pencil in
one of the reels and rotating.

• If the tape is loose, it may get

stretched, cut, or caught in the
cassette.

• Be careful not to touch the tape

surface.

• Avoid the following places to store the

tape:

– In dusty places
– In direct sunlight or heat
– In moist areas
– Near a magnet

Heads

Capstan

Pinch roller

Содержание UX-M3R


























Отзывы: