JVC UX-L30 Скачать руководство пользователя

Страница: 54 / 56

– 23 –

English

Maintenance

To get the best performance of the unit, keep your discs, tapes, and mechanism clean.

Handling discs

• Remove the disc from its case by

holding it at the edge while pressing
the center hole lightly.

• Do not touch the shiny surface of the

disc, or bend the disc.

• Put the disc back in its case after use

to prevent warping.

• Be careful not to scratch the surface of

the disc when placing it back in its
case.

• Avoid exposure to direct sunlight,

temperature extremes, and moisture.

To clean the disc

Wipe the disc with a soft cloth in a
straight line from center to edge.

DO NOT use any solvent—such as conventional record
cleaner, spray, thinner, or benzine—to clean the disc.

Handling cassette tapes

• If the tape is loose in its cassette, take

up the slack by inserting a pencil in
one of the reels and rotating.

• If the tape is loose, it may get

stretched, cut, or caught in the
cassette.

• Be careful not to touch the tape

surface.

• Avoid the following places to store the

tape:

— In dusty places
— In direct sunlight or heat
— In moist areas
— On a TV or speaker
— Near a magnet

Cleaning the unit

• Stains on the unit

Should be wiped off with a soft cloth. If the unit is heavily
stained, wipe it with a cloth soaked in water-diluted neutral
detergent and wrung well, then wipe clean with a dry cloth.

• Since the unit may deteriorate in quality, become

damaged or get its paint peeled off, be careful about the
followings.

— DO NOT wipe it with a hard cloth.
— DO NOT wipe it strong.
— DO NOT wipe it with thinner or benzine.
— DO NOT apply any volatile substance such as

insecticides to it.

— DO NOT allow any rubber or plastic to remain in

contact with it for a long time.

EN18-24_UX-L40&30[UW&UY]f

02.3.8, 10:39 AM

Содержание UX-L30

























































Результаты поиска

Содержание UX-L30

Отзывы:

Похожие инструкции для UX-L30

Бренды по названию

Популярные бренды

JVC UX-L30, Инструкция по эксплуатации

Результаты поиска

Содержание UX-L30

Отзывы:

Похожие инструкции для UX-L30

Бренды по названию

Популярные бренды