background image

Safety Precautions

IMPORTANT SAFEGUARDS

Electrical energy can perform many useful functions. This unit has been engineered and manufactured to assure 
your personal safety. But

 

IMPROPER USE CAN RESULT IN POTENTIAL ELECTRICAL SHOCK OR FIRE 

HAZARD.

 In order not to defeat the safeguards incorporated into this product, observe the following basic rules for 

its installation, use, and service. Please read these “IMPORTANT SAFEGUARDS” carefully before use.
•  All the safety and operating instructions should be read before the product is operated.
•  The safety and operating instructions should be retained for future reference.
•  All warnings on the product and in the operating instructions should be adhered to.
•  All operating instructions should be followed.

FCC NOTICE (U.S.A. only)
CAUTION:

 Changes or modifications not approved by JVC could void the user’s authority to operate the 

equipment.

NOTE:

 This equipment has been tested and found to comply with the limits for a Class B digital device, 

pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against 
harmful interference in a residential installation. This equipment generates, uses and can radiate radio 
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful 
interference to radio communications. However, there is no guarantee that interference will not occur in a 
particular installation. If this equipment does cause harmful interference to radio or television reception, which 
can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference 
by one or more of the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
– Consult the dealer or an experienced radio/TV technician for help.

WARNING: 

TO REDUCE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPARATUS TO 
RAIN OR MOISTURE. NO OBJECTS FILLED WITH LIQUIDS, SUCH AS VASES, SHALL BE 
PLACED ON THE APPARATUS.

2

02_TM-15L1D-EN2.indd   2

02_TM-15L1D-EN2.indd   2

06.11.14   9:52:26 AM

06.11.14   9:52:26 AM

Содержание TM-15L1D























Отзывы: