JVC TK-C215VP12E Скачать руководство пользователя страница 22 | Manualshive

Страница: 22 / 40

JVC TK-C215VP12E Скачать руководство пользователя страница 22

22

Installation and Connection

1.

Connecting the coaxial cable (

A

Pg. 17)

Lower the protection cover and connect the
connectors. Upon connecting, cover the
connectors using the protection cover.

2.

Connecting the AC 24 V/DC 12 V power

supply wires

Note:

●

To mount a heater (sold separately) to this
unit, make sure to connect it to an AC 24 V
supply during use.

3.

Connect the alarm cable.

(TK-C215VP12U/E only)(

A

Pg. 18)

4.

Binding the AC 24 V/DC 12 V power

supply wires and alarm signal wires (TK-
C215VP12U/E only) with insulating tape

Make sure to bind the connecting portions of AC
24 V/DC 12 V power supply wires and alarm
signal wires (TK-C215VP12U/E only) with
insulating tape.

5.

Wrap insulation tape around cables.

6.

Storing cables

Upon connecting, push the connector into the
cable storage space of the camera unit.

Note:

●

When mounting the camera to the electrical
box, push the connector into the electrical
box.

●

While the camera unit is disconnected from
the base, be extremely careful not to drop the
camera unit.

S
]

Cable Connection

1

3

2

4

Coaxial Cable

Protection Cover

Solder or Caulk

Insulating Tape

Bind
insulating
tape

AC 24 V/DC 12 V
Power Supply
Wire

Cable Storage
Space

*TK-C215VP12U/E is used in the above illustration

Alarm signal Wire
(TK-C215VP12 only)

TK-C215VP4_JP.book Page 22 Thursday, November 2, 2006 10:51 AM

«
...
20
21
22
23
24
...
»

Содержание TK-C215VP12E









































Отзывы:

Нет отзывов