Masterpage:Right-NoTitle0
EN
39
Filename [SR-VS30E_2-EN.fm]
Page 39
February 1, 2002 3:23 pm
H
Enter the programme date.
Press
DATE+/–
.
●
The current date appears on the TV screen. The date you enter
appears in its place.
I
Enter the channel position.
J
Set the tape speed.
Press
SP/LP
(
p
).
K
Set the VPS/PDC mode.
Press
VPS/PDC
to select “ON” or “OFF”.
●
If “VPS/PDC ON” is displayed on the TV screen or “VPS/PDC”
is lit on the front display panel, VPS/PDC is set to ON.
●
If “VPS/PDC OFF” is displayed on the TV screen or “VPS/PDC”
is not lit on the front display panel, VPS/PDC is set to OFF.
墌
“VPS/PDC Recording” in the right column
L
Return to the normal screen.
Press
PROG
or
OK
. “PROGRAM COMPLETED” appears
on the TV screen for about 5 seconds, then the normal
screen appears. If “PROGRAM OVERLAPPED” appears
on the TV screen and “Err” on the front display panel, see
page 43.
●
Repeat steps
3
–
12
for each additional programme.
M
Engage the recorder’s timer mode.
Press
#
(
TIMER
). The recorder turns off automatically and
“
#
” appears on the front display panel.
●
To disengage the timer mode, press
#
(
TIMER
) again.
To Timer-Record Weekly Or Daily Serials . . .
. . . anytime during steps
5
through
11
, press
WEEKLY
(
number
key
“
9
”) for weekly serials or
DAILY
(
number key
“
8
”) for daily
serials (Monday – Friday). Either “WEEKLY” or “DAILY” appears
on the TV screen. Pressing the button again makes the
corresponding indication disappear.
NOTES:
●
You can programme each deck to timer-record as many as 6
programmes. If you try to programme the recorder to record a
seventh, “PROGRAM FULL” appears on the TV screen and
“FULL” appears on the front display panel. To record the extra
programme, you must first cancel any unnecessary
programmes (
墌
pg. 42).
●
It is not possible to timer-record a satellite broadcast received
on the channel position “0” by the satellite receiver.
●
It is not possible to timer-record the same programme on both
the VHS deck and the DV deck simultaneously.
●
During timer recording, it is not possible to change the
recording deck (VHS or DV).
●
If the times that are programmed for recording on the DV deck
and on the VHS deck overlap, the earlier start time takes
precedence. If the start times are the same, the VHS deck takes
precedence.
Press
PR+/–
.
●
If you want to set a satellite
programme, press the
number
key “0”
to change “TV PROG”
to “SAT”, then press
PR+/–
.
Satellite Receiver Users
To timer-record a satellite broadcast using Express Timer
Programming:
A
Perform “Satellite Receiver Control Setting” on page 17.
B
Perform steps
1
–
13
. In step
9
, press the
number key
“
0
”
to change “TV PROG” to “SAT”. The front display panel
shows “L2” for the channel position. Then press
PR+/–
to
enter the channel position for the satellite broadcast. In
step
11
, you cannot set “VPS/PDC” to “ON”.
C
Leave the satellite receiver’s power on.
VPS/PDC Recording
Now available from some TV stations, PDC (Programme
Delivery Control) and VPS (Video Programme System) are
service designed to assure safe, accurate timer recording.
With this system, special code signals are transmitted
together with the audio/video signals. These code signals
control your video recorder and have precedence over the
advertised times you may have preset into the timer. This
means that your recorder will start and stop recording when
the preset TV programmes actually start and end — even if
the broadcast time of a preset TV programme is changed.
NOTES:
●
When you use Express Timer Programming, set the start time
(VPS or PDC time) exactly as advertised in the TV listing. A
different time than advertised will result in no recording.
●
VPS/PDC recording is also possible when a satellite receiver
or a cable system is connected to AV2 (L-2) IN/DECODER
connector on your recorder.
●
VPS/PDC recording is also possible via the AV1 (L-1) IN/OUT
connector.
How to check if the station being received transmits a
VPS/PDC signal (VHS deck only)
A
Press – –:– – until the channel position appears on the
front display panel.
B
Hold down
START+
for about 5 seconds.
“VPS/PDC” appears blinking on the front display panel.
If a VPS/PDC signal is detected from the station,
“VPS/PDC” will stop blinking.
If no VPS/PDC signal is detected from the station,
“VPS/PDC” will blink at a slower rate.
C
Press – –:– – or
START+
again to return to normal display.
SR-VS30E_1-EN.book Page 39 Friday, February 1, 2002 3:35 PM
Содержание SR-VS30E
Страница 90: ...90EN MEMO ...
Страница 91: ...EN 91 ...
