JVC SP-PWR1, Инструкция по эксплуатации

Страница: 47 / 100

Masterpage:Right+
Filename [TH-R1R3EU_06DVD Operation.fm]
Page 44Monday, 28 March 2005 21:23
BASIC OPERATIONS ON DVD DECK
44
You can enjoy radio broadcasts by browsing through all the
stations or using the preset memory function.
There is a time limit when performing the following setting. If the
time is up before completing the setting, re-perform from the
beginning.
Tuning In To Stations Manually
1
Press FM/AM to select the band.
Each time you press the button, the band switches between FM
and AM.
2
Press /– (
S
or
T
) until the desired station is
located.
NOTES:
●
A short press on
S
or
T
changes the frequency in 1 step FM
0.05 M/AM 9 K interval.
●
Press and hold
S
or
T
to change the frequency rapidly.
●
To auto tune stations, press
S
or
T
for a while then release.
●
A TUNED B lights on the front display panel when a station with
sufficient signal strength is tuned.
●
A ST B lights on the front display panel when a FM stereo
programme is received.
●
You can also press SOURCE on the front panel to select the
desired band in step 1 .
Preset Memory - Store Memory
Once a station is assigned to a channel number, the station can be
quickly tuned in. You can preset up to 30 FM and 15 AM stations.
1
Tune in to the station you want to preset.
2
Press MEMORY .
The preset number blinks on the
front display panel.
3
While blinking, press the number
keys or PR +/– to set the preset
number.
4
Press MEMORY .
87.80 MHz is assigned to FM1.
NOTES:
●
If no operation is carried out within 5 seconds when the display is
blinking, the preset will not be stored and the display changes
back to its original frequency.
●
When you have entered an input beyond the range using the
number keys , the preset number will return to 1 if you press
PR +/– .
●
Pressing the + and – key of PR +/– increases and decreases the
preset number by 1 respectively.
Preset Tuning
Press the number keys or PR +/– to tune to the station stored to
the preset number.
●
Number keys Can specify the preset number directly.
●
PR +/– Gradually increases or decreases the preset
number by 1 from the preset number of the
current reception.
To call up preset number 3
1
Press the number key
A
3
B
or
PR +/– to set to preset number 3.
●
The preset number blinks for a
few seconds before lighting up.
The preset number is fixed once
it lights up.
Switching The FM Mode
When an FM stereo broadcast is hard to receive or noisy, you can
change the FM reception mode while receiving an FM broadcast.
●
You can set the FM reception mode for each preset station.
1
Press FM MODE during FM reception.
Each time you press the button, the FM reception switches
between
A AUTO B and A MONO B .
●
MONO Setting
●
AUTO Setting
Receiving Radio Broadcasts
●
Turn on the unit.
●
Set the remote control selector switch to AUDIO .
●
Press FM/AM on the remote control.
1 2 3
4 5 6
7 8 9
0
VOL
SAT
TV
AUDIO
0-9
FM/AM
MEMORY
ENTER
/–
FM MODE
PR +/-
AUTO MUTING
Normally select this.
Stereo sound will be heard during stereo
broadcast, and monaural sound during
monaural broadcast.
This mode is also useful to suppress
static noise between stations.
MONO
Select this to improve the reception.
(However, stereo will not be effective.)
FM__ 87.80
Blinking
CH
FM 1 87.80
Blinking
CH
FM 1 87.80
CH
FM 3 108.00
Blinking
FM 3 88.60
CH
CH
MONO
AUTO
TH-R1R3EU_00.book Page 44 Monday, March 28, 2005 9:23 PM