JVC RV-DP200 Скачать руководство пользователя страница 61

Страница: 61 / 62

English

■

Troubleshooting

•

If you are having a problem with your System, check this list for a possible solution before calling for service.

•

If you cannot solve the problem from the hints given here, or the System has been physically damaged, call a qualified person, such as your

dealer, for service.

Symptom

Possible Cause

Action

No sound is heard.

•

Connections are incorrect, or loose.

•

Headphones are connected.

•

Check all connections and make correc-
tions. (See page 3.)

•

Disconnect the headphones.

Unable to record.

Cassette record protect tabs are removed.

Cover the holes on the back edge of the cas-
sette with tape.

Poor FM reception

The FM telescopic antenna is not properly
extended and positioned.

Fully extend the FM telescopic antenna and
turn it for the best reception.

The CD skips.

The CD is dirty or scratched.

Clean or replace the CD.

The CD does not play.

The CD is upside down.

Put the CD in with the label side up.

Unable to operate the Remote Control.

•

The path between the Remote Control
and the sensor on the Unit is blocked.

•

The batteries have lost their charge.

•

Remove the obstruction.

•

Replace the batteries.

Operations are disabled.

The built-in microprocessor has malfunc-
tioned due to external electrical interference.

Unplug the System then plug it back in after
a few minutes.

The cassette holder cannot be opened.

During tape playing, the power cord was
unplugged.

Plug in the power cord and press the
POWER button.

■

Specifications

Amplifier

Output Power

(Max.)

20 W (10 W + 10 W) at 4

Ω

(full range),

40 W (20 W + 20 W) at 4

Ω

, 60 Hz

(woofer)

Input Sensitivity/Impedance (1 kHz)

AUX IN

300 mV/47 kohms

MIC

200 ohms - 2 kohms (6.3 mm dia. plug)

GUITAR

100 kohms - 1 Mohm (6.3 mm dia. plug)

Output Sensitivity/Impedance (1 kHz)

Phones

16 ohms - 1 kohms
0 - 12 mW/ch output into 32 ohms

Cassette Deck

Frequency Response

TypeII (CrO

)

60 Hz - 14 kHz

Wow and Flutter

0.15% (WRMS)

CD Player

Wow And Flutter

Unmeasurable

Tuner

FM Tuner

Tuning Range

87.5 MHz - 108.0 MHz

AM Tuner

Tuning Range

530 kHz - 1 710 kHz

Antenna

FM telescopic antenna
Ferrite core antenna for AM

Speakers

Full range

8 cm (3 – 3/16")

4 44

ohms

Super woofer

16 cm (6 – 5/16")

4 ohms

General

Dimensions

634 mm

256.5 mm

311 mm (W/H/D)

(25"

10 – 1/8"

12 – 1/4")

Mass

10.2 kg (22.5 lbs) (without batteries)
11.3 kg (25 lbs) (with batteries)

Accessories

Power Cord (1)
Remote Control (1)
Shoulder Strap (1)

Power Specifications

Power Requirements AC 120 V ~ , 60 Hz

DC15V ("R20/D (13F)" batteries (10))
External DC12V (car battery via
optional CA-R120 car adaptor)

Power Consumption 45 watts (power on mode)

2 watts (in Standby mode)

Design and specifications are subject to change without notice.

RD-DP200(C)-Eng.fm Page 26 Monday, December 25, 2000 3:18 PM

Содержание RV-DP200































































Результаты поиска

Содержание RV-DP200

Отзывы:

JVC RV-DP200, Инструкция по эксплуатации, Страница: 61 / 62

Результаты поиска

Содержание RV-DP200

Отзывы: