JVC MX-K5 Скачать руководство пользователя страница 14 | Manualshive

Страница: 14 / 73

background image

MX-K5/MX-K6

1-14

Prior to performing the following procedure, remove
the CD tray.

Detach the belt from the pulley on the upper side of
the CD changer unit (Do not stain the belt with
grease).

Disconnect the card wire from the pickup unit
connector on the under side of the CD changer unit.

Attention : Solder is put up before the card wire is
removed from the pick-up unit
connector on the CD mechanism
assembly.
(When the card wire is removed without
putting up solder, the CD pick-up unit
assembly might destroy.)

Disconnect the motor wire harness from connector
on the CD servo board.

Remove the screw Z attaching the switch board and
release the two tabs k attaching the switch board
outward and detach the switch board.

Remove the two screws A' attaching the CD servo
board and . First release the n side of the two tabs l
and two tabs m attaching the CD servo board motor
to raise the CD servo board slightly, then release the
CD servo board.

If the tabs l and m are hard to release, it is
recommendable to unsolder the two soldered parts
on the motor terminal of the CD servo board.

1.

2.

3.

4.

5.

Removing the belt, the CD servo board
and the switch board (See Fig.33 and 34)

Soldering

Card wire

Pickup unit
connector

Fig.34

Fig.33

Belt

CD changer unit

A'

CD servo board

Tabs m

Tabs l

Soldered parts

Motor

Switch board

Z

CW3

Tabs k

CD mechanism board

motor connector

Pickup unit connector

«
...
12
13
14
15
16
...
»

Содержание MX-K5










































































Отзывы:

Нет отзывов

Похожие инструкции для MX-K5

Бренд: Oklahoma Sound Страницы: 4

Бренд: B&W electronics Страницы: 13

Бренд: EAW Страницы: 91

Бренд: EAW Страницы: 4

Бренд: EAW Страницы: 4

Бренд: EAW Страницы: 2

Бренд: EAW Страницы: 16

Бренд: EAW Страницы: 5

Бренд: EAW Страницы: 20

Бренд: GAIT Страницы: 2

OTC ARXIS pulse P403L

Бренд: Daihen Страницы: 188

Pure Link 1300 Series

Бренд: lancer Страницы: 20

Бренд: Pure Acoustics Страницы: 1

Бренд: Valcom Страницы: 2

Бренд: Electro-Voice Страницы: 2

Бренд: Gemini Страницы: 10

Бренд: EAW Страницы: 2

CARPOWER CRB-130SET

Бренд: Monacor Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды