JVC KW-AVX735, Инструкция по эксплуатации, Страница: 64 / 64

(TEL MUTING)
(PARKING BRAKE)
(GND)
(POWER ANTENNA)
(ILLUMINATION CONTROL)
MIC IN SUBWOOFER OUT
REVERSE
GEAR
SIGNAL
*
1
*
1
*
2
*
2
1
2
3
4
5
9
6
7
8
2
3 1
Ignition switch
KW-AVX836/KW-AVX835
KW-AVX736/KW-AVX735
KW-AVX836/KW-AVX835
KW-AVX736/KW-AVX735
*
4
*
4
*
4
*
5 *
5
*
5
MIC IN
KW-AVX836
KW-AVX835
KW-AVX836/KW-AVX835
KW-AVX736/KW-AVX735
*
6
*
4
*
6
*
4
KW-AVX 8 36
KW-AVX 8 35
KW-AVX736
KW-AVX735
KW-AVX836/KW-AVX835
KW-AVX736/KW-AVX735
KW-AVX 8 36/KW-AVX 8 35
KW-AVX736/KW-AVX735
2
Before connecting: Check the wiring in the vehicle carefully. Incorrect connection may cause serious damage to this unit.
The leads of the power cord and those of the connector from the car body may be different in color.
1
Connect the colored leads of the power cord in the order specified in the illustration below.
2
Connect the antenna cord.
3
Finally connect the wiring harness to the unit.
•
The terminals and cables of all models are shown in the illustration for the purpose of explanation.
See each diagram below.
Only for KW-AVX836/KW-AVX835 :
Insert the Bluetooth adapter KS-UBT1 on the
front of the unit. See diagram
‰ below.
Black
Yellow
* 3
Red
Orange with white stripe
Brown
Light green
Blue with white stripe
Blue
To parking brake (see page 1)
To metallic body or chassis of the car
To a live terminal in the fuse block connecting to the car battery
(bypassing the ignition switch) (constant 12 V)
To an accessory terminal in the fuse block
To car light control switch
To mobile phone system
To automatic antenna is any (250 mA max.)
To the remote lead of other equipment (200 mA max.)
Crimp connector
White with black stripe White Gray with black stripe Gray Green with black stripe Green Purple with black stripe Purple
Left speaker
(front) Right speaker
(front) Left speaker
(rear) Right speaker
(rear)
15 A fuse Fan Rear ground
terminal
Antenna
terminal
Connecting to the steering wheel remote controller
If your car is equipped with the steering wheel remote controller, you can operate this unit using the
controller. For connection, an exclusive remote adapter (not supplied) which matches your car is
required. For details, consult the same car audio dealer as where the unit is purchased.
A
OE remote adapter
*
2
Steering wheel remote controller (equipped in the car)
Connecting the external amplifiers and subwoofer
You can connect an amplifier to upgrade your car stereo system.
• Connect the remote lead (blue with white stripe) to the remote lead of the other equipment so that it
can be controlled through this unit.
• Disconnect the speakers from this unit, and connect them to the amplifier. Leave the
speaker leads of this unit unused.
• You can switch off the built-in amplifier and send the audio signals only to the external amplifier(s) to
get clear sounds and to prevent internal heat built-up inside the unit.
See page 30 of the INSTRUCTIONS.
B
Subwoofer
JVC
Amplifier
JVC Amplifier
JVC
Amplifier
Remote lead
*
2
Rear
speakers
Front
speakers
To the remote lead of other equipment
Remote lead (blue
with white stripe)
Y-connector
*
2
Connecting the microphone (Only for KW-AVX836/KW-AVX835)
E
Secure the microphone cord using cord cramps (not supplied) if necessary.
or
Microphone clip
Microphone
holder
Adhesive tape
Microphone
Inserting the Bluetooth adapter (Only for KW-AVX836/KW-AVX835)
1
2
1
Turn on the power
then open the monitor
panel (see page 6 of the
INSTRUCTIONS).
2
Insert the Bluetooth
adapter with the JVC logo
facing upside.
3
Close the monitor panel.
We recommend to attach the
microphone near the steering
wheel using the microphone
holder.
Bluetooth adapter
(KS-UBT1)
(Press)
Connecting the external components
D
Camcorder
etc.
External
monitor
KV-CM1
*
2
Rear view camera
*
1
USB devices
USB cable (approx. 1.2 m)
USB device
Connecting the iPod or the iPhone
KS-U30
(not supplied)
USB 2.0 cable (accessory of the
iPod/iPhone)
–
To watch the video: USB Audio and Video cable for iPod/iPhone—KS-U30 (not supplied)
*
7
–
To listen to the music: USB 2.0 cable (accessory of the iPod/iPhone)
Connecting an external navigation box
C
(see page 1
)
* 1
Only for KW-AVX836/KW-AVX835.
* 2
Not supplied for this unit.
* 3
Before checking the operation of this unit prior to installation, this lead
must be connected, otherwise power cannot be turned on.
Do not connect the lead directly to the battery.
* 4
Audio cord (not supplied for this unit).
* 5
Firmly attach the ground wire to the metallic body or to the chassis of
the car—to the place uncoated with paint (if coated with paint, remove
the paint before attaching the wire). Failure to do so may cause damage
to the unit.
* 6
Video cord (not supplied for this unit).
* 7
When using the cable, you need to change the setting on the unit (see
page 19 of the INSTRUCTIONS).
•
iPod is a trademark of Apple Inc., registered in the U.S. and
other countries.
•
iPhone is a trademark of Apple Inc.
Connect an external navigation box to the RGB input terminal.
The positional information detected on the touch panel and picture signals from the navigation box are
transferred through the terminal.
Refer to the manual of the external
navigation box for details.
• Please contact your dealer to inquire about
compatible navigation boxes.
• JVC cannot guarantee proper operation of the external devices connected to the RGB input terminal.
External
navigation
box
* 2
RGB input terminal
Fuse block
1-2_KWAVX836[U]_f.indd 2 1-2_KWAVX836[U]_f.indd 2 10.1.20 1:08:01 PM 10.1.20 1:08:01 PM