JVC KD-SX930 Скачать руководство пользователя

Страница: 29 / 30

ENGLISH

AUDIO AMPLIFIER SECTION

Maximum Power Output:

Front: 40 watts per channel
Rear: 40 watts per channel

Continuous Power Output (RMS):

Front: 16 watts per channel into 4

Ω

, 40

to 20,000 Hz at no more than 0.8%
total harmonic distortion.

Rear: 16 watts per channel into 4

Ω

, 40

to 20,000 Hz at no more than 0.8%
total harmonic distortion.

Load Impedance: 4

Ω

(4 to 8

Ω

allowance)

Tone Control Range:

Bass: ±10 dB at 100 Hz
Treble:±10 dB at 10 kHz

Frequency Response: 40 to 20,000 Hz
Signal-to-Noise Ratio: 70 dB
Line-Out Level/Impedance: 2.0 V/20 k

Ω

load

(full scale)

Output Impedance: 1 k

Ω

TUNER SECTION

Frequency Range:

FM: 87.5 to 107.9 MHz

(with channel interval set to 200 kHz)
87.5 to 108.0 MHz
(with channel interval set to 50 kHz)

AM: 530 to 1,710 kHz

(with channel interval set to 10 kHz)
531 to 1,602 kHz
(with channel interval set to 9 kHz)

[FM Tuner]
Usable Sensitivity: 11.3 dBf (1.0 µV/75

Ω

)

50 dB Quieting Sensitivity:

16.3 dBf (1.8 µV/75

Ω

)

Alternate Channel Selectivity (400 kHz):

65 dB

Frequency Response: 40 to 15,000 Hz
Stereo Separation: 35 dB
Capture Ratio: 1.5 dB

[AM Tuner]
Sensitivity: 20 µV
Selectivity: 35 dB

CD PLAYER SECTION

Type: Compact disc player
Signal Detection System: Non-contact optical

pickup (semiconductor laser)

Number of channels: 2 channels (stereo)
Frequency Response: 5 to 20,000 Hz
Dynamic Range:

KD-SX939: 96 dB
KD-SX930: 95 dB

Signal-to-Noise Ratio:

KD-SX939: 98 dB
KD-SX930: 97 dB

Wow and Flutter: Less than measurable limit

GENERAL

Power Requirement:

Operating Voltage: DC 14.4 volts (11 to
16 volts allowance)

Grounding System: Negative ground
Dimensions (W x H x D):

Installation Size: 182 x 52 x 150 mm

(7-3/16" x 2-1/16" x 5-15/16")

Panel Size: 188 x 58 x 14 mm

(7-7/16" x 2-5/16" x 5/8")

Mass: 1.4

(3.1 lbs) (excluding accessories)

Design and specifications subject to change
without notice.

If a kit is necessary for your car, consult
your telephone directory for the nearest
car audio speciality shop.

SPECIFICATIONS

27-29.KD-SX939/SX930

98.2.25, 10:45 AM

Содержание KD-SX930































Результаты поиска

Содержание KD-SX930

Отзывы:

Похожие инструкции для KD-SX930

Бренды по названию

Популярные бренды

JVC KD-SX930, Инструкция по эксплуатации

Результаты поиска

Содержание KD-SX930

Отзывы:

Похожие инструкции для KD-SX930

Бренды по названию

Популярные бренды