(No.YA015)1-11
SECTION 3
DISASSEMBLY
3.1
DISASSEMBLY PROCEDURE
NOTE:
Since this model adopts a layer structure, follow the procedure below in disassembling this model.
Be careful enough not to damage or scratch parts.
3.1.1 REMOVING THE STAND
(1) Remove the 2 screws [A], and remove the STAND
COVER.
(2) Remove the 4 screws [B], and remove the STAND.
3.1.2 REMOVING THE REAR COVER
• Remove the STAND.
(1) Remove the JACK COVER (L/R).
(2) Remove the 7 screws [C], 3 screws [D], and 2 screws [E]
(12 screws in total).
(3) Remove the REAR COVER.
3.1.3 REMOVING THE REGULATOR PWB / COOLING FAN
• Remove the STAND.
• Remove the REAR COVER.
(1) Pull out the wire of COOLING FAN.
(2) Remove the 5 screws [F], and remove the FAN BRACKET.
(3) Remove the 2 screws [Y], and remove the COOLING FAN.
(4) Remove the REGULATOR PWB.
3.1.4 REMOVING THE RECEIVER PWB
• Remove the STAND.
• Remove the REAR COVER.
• Remove the FAN BRACKET.
(1) Remove the 2 screws [G] and 3 screws [H] (5 screws in
total). Then, remove the TERMINAL BASE.
(2) Remove the 6 screws [J], and remove the RECEIVER
PWB.
3.1.5 REMOVING THE FRONT CONTROL PWB CONTROL /
FRONT SENSOR PWB
• Remove the STAND.
• Remove the REAR COVER.
(1) Remove the 2 screws [K], and remove the CONTROL
KNOB.
(2) Remove the 2 screws [L], and remove the FRONT
CONTROL PWB.
(3) Remove the FRONT SENSOR PWB.
3.1.6 REMOVING THE VIDEO PWB / MI-COM & DIST
MODULE PWB
• Remove the STAND.
• Remove the REAR COVER.
• Remove the FAN BRACKET.
(1) Remove the 1 screw [M] and 1 screw [N]. Then, remove the
JACK BASE.
(2) Remove the 4 screws [P], and remove the VIDEO PWB.
(3) Remove the 6 screws [R], and remove the VIDEO PWB
BRACKET.
(4) Remove the 4 screws [S], and remove the MI-COM & DIST
MODULE PWB form the VIDEO PWB BRACKET.
3.1.7 REMOVING THE POWER PWB
• Remove the STAND.
• Remove the REAR COVER.
• Remove the FAN BRACKET.
• Remove the RECEIVER PWB.
(1) Remove the 4 screws [T], and remove the RECEIVER
PWB BRACKET.
(2) Remove the 1 screw [U], and remove the POWER CORD
HOLDER.
(3) Remove the 5 screws [V], and 1 screw [W] . Then, remove
the POWER PWB.
(4) Remove the 4 screws [X], and remove the CHASSIS
BASE.
3.1.8 REMOVING THE TUNER PWB / MSP PWB
• Remove the STAND.
• Remove the REAR COVER.
(1) Remove the 2 screws [Q], and remove the TUNER PWB
BASE.
(2) Remove the 4 screws [Z], and remove the TUNER PWB
and MSP PWB.
Содержание InteriArt LT-32C31BJE
