background image

EN 

15

    

SP

EP

VCR

BASIC PLAYBACK AND RECORDING

Basic
Playback

This VCR can check the tape condition during playback
(and recording), and realizes the best possible pictures.

1

Load a cassette

Make sure the window side is up, the rear label
side is facing you and the arrow on the front of
the cassette is pointing towards the VCR.
Do not apply too much pressure when inserting.

The VCR turns on automatically.

The counter is automatically reset to “0:00:00”.

If the cassette’s record safety tab has been
removed, playback begins automatically.

2

Start playback

Press PLAY ( 

3

 ).

Tape speed (SP or EP) is automatically detected.

If “VIDEO CALIBRATION” is set to “ON” (default
setting: 

Z

 pg. 33), “VIDEO CALIBRATION” ap-

pears on the screen, and this VCR checks the tape
condition during automatic tracking.

To stop playback

Press STOP ( 

7

 ) on the Remote or STOP/EJECT ( 

7

 

0

 )

on the front panel.

To rewind the tape

Press REW ( 

1

 ).

To fast-forward the tape

Press FF ( 

¡

 ).

To eject the tape

Press STOP/EJECT ( 

7

 

0

 ) on the front panel when the

tape is not running.

 You can also eject the cassette with the VCR turned off.

To turn off the VCR

Press POWER.

Turn on the VCR and the TV, and select the VCR
channel 3 or 4 (or AV mode) on the TV.

Usable cassettes

Full-Size VHS
T-30 (ST-30**)
T-60 (ST-60**)
T-90
T-120 (ST-120**)
T-160 (ST-160**)
ST-210**
Compact VHS*
TC-20 (ST-C20**)
TC-30 (ST-C30**)
TC-40 (ST-C40**)
* Compact VHS camcorder recordings can be

played on this VCR. Simply place the recorded
cassette into a VHS Cassette Adapter and it can be
used just like any full-sized VHS cassette.

** This VCR can record on regular VHS and Super

VHS cassettes. However, it will record regular VHS
signals only.

INFORMATION

This VCR is equipped with SQPB (S-VHS QUASI
PLAYBACK) that lets you watch tapes recorded in the S-
VHS format with regular VHS resolution.

SQPB does not deliver Super VHS resolution.

S-VHS recording is not possible with this VCR.

Clean the video heads using a dry
cleaning cassette — TCL-2UX —
when:

• Rough, poor picture appears while a tape is played

back.

• The picture is unclear or no picture appears.
• “USE CLEANING CASSETTE” appears on the screen

(only with “SUPERIMPOSE” set to “ON”: 

Z

 pg. 33.)

FF ( 

¡

 )

2

STOP/EJECT

7

 / 

0

 )

POWER

REW (

1

 )

1

2

3

4

5

6

7

8

9

0

2

4

1

3

2

STOP ( 

7

 )

FF ( 

¡

 )

REW ( 

1

 )

POWER

Содержание HR-VP683U





















































Отзывы: