JVC GR-AXM10 Скачать руководство пользователя

Страница: 18 / 60

RECORDING

Basic Features

FEATURE:

Zooming

PURPOSE:

Varies the focal length of the lens
and produces the zoom in/out effect.

OPERATION:

Zoom In

1) Push the power zoom lever down

toward “T”.

Zoom Out

1) Push the lever up toward “W”.

NOTES:

●

The further the power zoom lever
is pushed, the faster the zoom
speed becomes.

●

Focusing may become unstable
during zooming. In this case, set
the zoom while in Record–
Standby, set manual focus or Focus
Lock (

pgs. 22, 23), then zoom

in or out in Record mode.

FEATURE:

Quick Review

PURPOSE:

To check the end of the last record-
ing.

OPERATION:

1) Press “

” and release quickly

during the Record–Standby mode.
•Tape is rewound for about 2

seconds and played back
automatically, then pauses in
Record–Standby mode for the
next shot.

NOTE:

Distortion may occur at start of
playback. This is normal.

FEATURE:

Retake

PURPOSE:

To re-record certain segments.

OPERATION:

1) Make sure the camcorder is in the

Record–Standby mode.

2) Press either RETAKE button to

reach the start point for new
recording.
Pressing “F” fast-forwards the tape
and pressing “R” reverses it.

3) Press Recording Start/Stop to start

recording.

NOTE:

Noise may appear during Retake.
This is normal.

Zoom-out

Zoom-in

RETAKE (R/F)

Power zoom lever

Zoom indicator

Содержание GR-AXM10





























































Результаты поиска

Содержание GR-AXM10

Отзывы:

Похожие инструкции для GR-AXM10

Бренды по названию

Популярные бренды

JVC GR-AXM10, Инструкция по эксплуатации

Результаты поиска

Содержание GR-AXM10

Отзывы:

Похожие инструкции для GR-AXM10

Бренды по названию

Популярные бренды