JVC DR-DX5SEK, Инструкция по эксплуатации

Страница: 70 / 92

Filename [DX5SEK_12Editing.fm]
Masterpage:Left0
70
EN
Page 70 Thursday, 10 November 2005 16:34
SYSTEM CONNECTIONS
Connect the satellite receiver to the [L-2 IN/DECODER] connector,
then connect the [L-1 IN/OUT] connector to the TV’s connector.
NOTES:
●
Set
A
L-2 SELECT
B
to
A
VIDEO
B
or
A
S-VIDEO
B
. (
A
pg. 64)
●
You can use the Automatic Satellite Programme Recording
function (
A
pg. 50) with this connection. (HDD deck only)
●
To record a programme via the satellite receiver, select L-2 mode
by pressing
PR +/– so that
A
L-2
B
appears on the front display
panel.
●
For details, refer to the instruction manual of the satellite receiver.
These instructions enable you to connect your unit to a Dolby
Digital Decoder or an amplifier with built-in DTS.
1
Connect the unit and a Dolby Digital Decoder or an amplifier
with built-in DTS using either an optional optical cable or an
optional coaxial cable.
NOTES:
●
For Dolby Digital sound, set A DIGITAL AUDIO OUT B to A DOLBY
DIGITAL/PCM B . (
A
pg. 71)
●
For DTS sound, set A DIGITAL AUDIO OUT B to A STREAM/PCM B .
(
A
pg. 71)
CAUTIONS:
●
This unit has a dynamic range of more than 110 dB with regards
to its Hi-Fi audio capability. It is recommended that you check the
maximum level if you are going to listen to the Hi-Fi audio signals
through a stereo amplifier. A sudden surge in the input level to
the speakers may damage them.
●
Some speakers and televisions are specially shielded to prevent
television interference. If both are of the non-shielded type, do not
place the speakers adjacent to the TV set as this can adversely
affect the playback picture.
When you can’t switch the audio channel of a bilingual
programme
When the unit is connected with a digital audio device using an
optional optical cable and
A DIGITAL AUDIO OUT B is set to
A DOLBY DIGITAL/PCM B , it is not possible to switch the audio
channel of a bilingual programme recorded on a DVD-RAM or
DVD-RW (VR mode) disc. In this case, perform the following steps
using the remote control to switch
A DIGITAL AUDIO OUT B from
A DOLBY DIGITAL/PCM B to A PCM ONLY B .
A
Press SET UP to access the Main Menu screen.
B
Press selection keys to select A DVD VIDEO SET UP B , then press
G
.
C
Press selection keys to select A AUDIO OUTPUT B , then press
G
.
D
Press selection keys to select A DIGITAL AUDIO OUT B , then
press ENTER .
E
Press selection keys to select A PCM ONLY B , then press
ENTER . (
A
pg. 71)
F
Press SET UP to complete the setting.
G
Press AUDIO to select the desired audio channel.
Connecting To A Satellite Receiver
IMPORTANT
When you set A L-2 SELECT B to A SAT VIDEO B or A SAT
S-VIDEO B (
A
pg. 64), it is possible to view a satellite broadcast
with the TV set to its AV mode even if the unit is turned off. When
the unit is in Stop mode or recording, press
TV AV/VIDEO on the
remote control to turn off the VIDEO indicator on the front
display panel.
●
If you turn on the unit when the satellite receiver’s power is off,
nothing appears on the TV screen. In this case, turn on the
satellite receiver, or set the TV to its TV mode, or press
TV AV/
VIDEO on the remote control to set the unit to the AV mode.
Outdoor unit
Satellite cable
Satellite receiver
Aerial
TV aerial cable
ANTENNA OUT
ANTENNA IN
TV
Connecting To A Dolby Digital Decoder
Or An Amplifier With Built-in DTS
Dolby Digital Decoder or
amplifier with built-in DTS
Coaxial cable
(not supplied)
Rear of unit
Note for connection:
Remove the protection cap from the optical cable.
To [DIGITAL AUDIO
OUT (COAXIAL)]
To DIGITAL AUDIO input
Optical cable
(not supplied)
To [DIGITAL AUDIO
OUT (OPTICAL)]
DX5SEK_00.book Page 70 Thursday, November 10, 2005 4:35 PM