JVC DR-DX5SE, Инструкция по эксплуатации

Страница: 64 / 92

Filename [DX5SEU_12Editing.fm]
Masterpage:Left+
64
EN
EDITING
Page 64 Wednesday, 23 November 2005 14:13
SAT S-VIDEO
:
If a connected satellite receiver’s output is compatible with Y/C
signals, set to
A SAT S-VIDEO B . (For connection, be sure to use
a 21-pin SCART cable that is compatible with the Y/C signal.)
DECODER
:
To use a decoder connected to the [L-2 IN/DECODER]
connector.
NOTES:
●
If you have a satellite receiver or a decoder connected to the [L-2
IN/DECODER] connector, be sure to set
A L-2 SELECT B back to
appropriate mode after editing.
●
If you are not connecting a satellite receiver or a decoder to the
[L-2 IN/DECODER] connector, leave
A L-2 SELECT B set to
A VIDEO B .
●
When A L-2 SELECT B is set to A SAT VIDEO B and A SAT
S-VIDEO B , A SAT B appears on the TV screen or front display
panel instead of A L-2 B .
●
If A L-1 OUTPUT B is set to A SCART S-VIDEO B , it is not possible
to set A L-2 SELECT B to A DECODER B or A SAT VIDEO B .
●
If A L-1 OUTPUT B is set to A SCART RGB B , it is not possible to set
A L-2 SELECT B to A DECODER B or A SAT S-VIDEO B .
●
If A L-1 OUTPUT B is set to A COMPONENT B and A L-2 SELECT B
to A SAT VIDEO B , A SAT S-VIDEO B or A DECODER B , be sure to
connect the [L-1 IN/OUT] connector with a TV.
●
If A L-2 SELECT B is set to A SAT S-VIDEO B , be sure to set A L-1
OUTPUT B to A SCART S-VIDEO B .
●
The S-Video output does not support the satellite receiver
function. Make use of the L-1 output when viewing images from
the satellite receiver.
F-1 Input Setting
Set A F-1 INPUT B to the appropriate mode depending on the
connector (VIDEO or S-VIDEO) being used on the front panel.
1
Perform steps 1 and 2 of A L-1 Output And L-1 Input Setting B
(
A
pg. 63).
2
Press selection keys to select A F-1 INPUT B , then press
ENTER .
3
Press selection keys to select
the appropriate setting, then
press
ENTER .
4
Press SET UP to complete the
setting.
* The boldface settings below indicate the settings at your purchase.
8
F-1 INPUT
^
VIDEO
/ S-VIDEO
VIDEO
:
When connecting an appliance to the [VIDEO] input connector,
set to
A VIDEO B .
S-VIDEO :
When connecting an appliance to the [S-VIDEO] input
connector, set to
A S-VIDEO B
.
You can dub selected audio from a DVD or Audio CD disc to a
digital audio device.
However, it is not possible to dub copy-protected discs.
Example: Dubbing to an MD
1
Connect the unit and a digital audio device using either an
optional optical cable or an optional coaxial cable.
2
Place a disc on the unit and load an MD on the connected
digital audio device.
3
Select the audio to be dubbed.
4
Start playback slightly before the actual point from where you
wish to start dubbing.
5
Press
W
to pause playback.
6
Select the input mode on the connected digital audio device.
7
Press
I
to start playback on the unit.
8
Start recording on the digital audio device.
9
Stop recording on the digital audio device. Then press
o
to stop
playback on the unit.
NOTE:
There may be a discrepancy of several seconds between where
you intend editing to start, and where it actually starts.
ENTER
SELECT
SET UP
EXIT
DVD VIDEO SET UP
MONITOR TYPE
HDD/DVD/DV SET UP FUNCTION SET UP INITIAL SET UP
REC/PLAY SET UP DISPLAY SET
F-1 INPUT
L-1 INPUT
L-1 OUTPUT
L-2 SELECT
VIDEO IN/OUT
4:3LB
VIDEO
VIDEO
SCART VIDEO
VIDEO
VIDEO
VIDEO
S-VIDEO
SELECT WITH @ THEN PRESS [ENTER]
PRESS [SET UP] TO EXIT
Digital Audio Dubbing
●
Turn on the TV and select the AV mode.
●
Slide the TV/CABLE/SAT/DVD switch to DVD .
Rear of unit
Note for connection:
Remove the protection cap from the optical cable.
Digital audio device
(MD deck, etc.)
Coaxial cable
(not supplied)
Player
Recorder
To [DIGITAL AUDIO
OUT (COAXIAL)]
To [DIGITAL AUDIO
OUT (OPTICAL)]
Optical cable
(not supplied)
DX5SEU_00.book Page 64 Wednesday, November 23, 2005 2:13 PM